rendered paste body/proc/asound/cards
0 [Audigy2 ]: Audigy2 - Audigy 2 ZS [SB0350]
Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) at 0x3000, irq 24
1 [CK804 ]: NFORCE - NVidia CK804
NVidia CK804 with AD1981B at irq 22
/proc/asound/card0/codec97#0/ac97#0-0
0-0/0: SigmaTel STAC9750,51
PCI Subsys Vendor: 0x0000
PCI Subsys Device: 0x0000
Capabilities : -headphone out-
DAC resolution : 20-bit
ADC resolution : 20-bit
3D enhancement : SigmaTel 3D Enhancement
Current setup
Mic gain : +0dB [+0dB]
POP path : pre 3D
Sim. stereo : off
3D enhancement : off
Loudness : off
Mono output : MIX
Mic select : Mic1
ADC/DAC loopback : off
Extended ID : codec=0 rev=1 AMAP DSA=0 SPDIF VRA
Extended status : SPCV SPDIF=7/8
PCM front DAC : 48000Hz
PCM ADC : 48000Hz
SPDIF Control : Consumer PCM Copyright Category=0x0 Generation=0 Rate=48kHz
/proc/asound/card0/codec97#0/ac97#0-0+regs
0:00 = 6a90
0:02 = 0000
0:04 = 1f1f
0:06 = 801f
0:08 = 0000
0:0a = 801e
0:0c = 801f
0:0e = 801f
0:10 = 9f1f
0:12 = 9f1f
0:14 = 9f1f
0:16 = 9f1f
0:18 = 9f1f
0:1a = 0000
0:1c = 0000
0:1e = 0000
0:20 = 0000
0:22 = 0000
0:24 = 0000
0:26 = 000f
0:28 = 0605
0:2a = 0410
0:2c = bb80
0:2e = 0000
0:30 = 0000
0:32 = bb80
0:34 = 0000
0:36 = 0000
0:38 = 0000
0:3a = 2000
0:3c = 0000
0:3e = 0100
0:40 = 0000
0:42 = 0000
0:44 = 0000
0:46 = 0000
0:48 = 0000
0:4a = 0000
0:4c = 0003
0:4e = ffff
0:50 = 0000
0:52 = 0000
0:54 = 0000
0:56 = 0000
0:58 = 0000
0:5a = 0000
0:5c = 0000
0:5e = 0000
0:60 = 0000
0:62 = 0000
0:64 = 0000
0:66 = 0000
0:68 = 0000
0:6a = 0000
0:6c = 0002
0:6e = 1000
0:70 = 0000
0:72 = 0000
0:74 = 0800
0:76 = 0000
0:78 = 0000
0:7a = 0000
0:7c = 8384
0:7e = 7650
/proc/asound/card1/codec97#0/ac97#0-0
0-0/0: Analog Devices AD1981B
PCI Subsys Vendor: 0x10f1
PCI Subsys Device: 0x2895
Capabilities : -headphone out-
DAC resolution : 20-bit
ADC resolution : 16-bit
3D enhancement : No 3D Stereo Enhancement
Current setup
Mic gain : +0dB [+0dB]
POP path : pre 3D
Sim. stereo : off
3D enhancement : off
Loudness : off
Mono output : MIX
Mic select : Mic1
ADC/DAC loopback : off
Extended ID : codec=0 rev=1 AMAP DSA=0 SPDIF VRA
Extended status : SPCV SPDIF=7/8 VRA
PCM front DAC : 48000Hz
PCM ADC : 48000Hz
SPDIF Control : Consumer PCM Copyright Category=0x22 Generation=1 Rate=48kHz
AD18XX configuration
Unchained : 0x1000,0x0000,0x0000
Chained : 0x0000,0x0000,0x0000
/proc/asound/card1/codec97#0/ac97#0-0+regs
0:00 = 0090
0:02 = 1f1f
0:04 = 1f1f
0:06 = 801f
0:08 = 0000
0:0a = 0000
0:0c = 801f
0:0e = 801f
0:10 = 9f9f
0:12 = 9f9f
0:14 = 0000
0:16 = 9f9f
0:18 = 9f9f
0:1a = 0000
0:1c = 0000
0:1e = 0000
0:20 = 0000
0:22 = 0000
0:24 = 0000
0:26 = 000f
0:28 = 0605
0:2a = 0411
0:2c = bb80
0:2e = 0000
0:30 = 0000
0:32 = bb80
0:34 = 0000
0:36 = 0000
0:38 = 0000
0:3a = 2a20
0:3c = 0000
0:3e = 0000
0:40 = 0000
0:42 = 0000
0:44 = 0000
0:46 = 0000
0:48 = 0000
0:4a = 0000
0:4c = 0000
0:4e = 0000
0:50 = 0000
0:52 = 0000
0:54 = 0000
0:56 = 0000
0:58 = 0000
0:5a = 0000
0:5c = 4000
0:5e = 0000
0:60 = 8080
0:62 = 0000
0:64 = 8000
0:66 = 0000
0:68 = 0000
0:6a = 0000
0:6c = 0000
0:6e = 0000
0:70 = 0000
0:72 = 0000
0:74 = 1001
0:76 = 2010
0:78 = 0000
0:7a = 0000
0:7c = 4144
0:7e = 5374
/proc/asound/pcm
01-02: Intel ICH - IEC958 : NVidia CK804 - IEC958 : playback 1
01-01: Intel ICH - MIC ADC : NVidia CK804 - MIC ADC : capture 1
01-00: Intel ICH : NVidia CK804 : playback 1 : capture 1
00-04: p16v : p16v : playback 1 : capture 1
00-03: emu10k1 : Multichannel Playback : playback 1
00-02: emu10k1 efx : Multichannel Capture/PT Playback : playback 8 : capture 1
00-01: emu10k1 mic : Mic Capture : capture 1
00-00: emu10k1 : ADC Capture/Standard PCM Playback : playback 32 : capture 1
$ lshal -l
Dumping 125 device(s) from the Global Device List:
-------------------------------------------------
udi = '/org/freedesktop/Hal/devices/computer'
info.addons = {'hald-addon-cpufreq', 'hald-addon-acpi'} (string list)
info.bus = 'unknown' (string)
info.callouts.add = {'hal-storage-cleanup-all-mountpoints'} (string list)
info.interfaces = {'org.freedesktop.Hal.Device.SystemPowerManagement'} (string list)
info.product = 'Computer' (string)
info.subsystem = 'unknown' (string)
info.udi = '/org/freedesktop/Hal/devices/computer' (string)
org.freedesktop.Hal.Device.SystemPowerManagement.method_argnames = {'num_seconds_to_sleep', 'num_seconds_to_sleep', '', '', '', 'enable_power_save'} (string list)
org.freedesktop.Hal.Device.SystemPowerManagement.method_execpaths = {'hal-system-power-suspend', 'hal-system-power-suspend-hybrid', 'hal-system-power-hibernate', 'hal-system-power-shutdown', 'hal-system-power-reboot', 'hal-system-power-set-power-save'} (string list)
org.freedesktop.Hal.Device.SystemPowerManagement.method_names = {'Suspend', 'SuspendHybrid', 'Hibernate', 'Shutdown', 'Reboot', 'SetPowerSave'} (string list)
org.freedesktop.Hal.Device.SystemPowerManagement.method_signatures = {'i', 'i', '', '', '', 'b'} (string list)
power_management.acpi.linux.version = '20070126' (string)
power_management.can_hibernate = false (bool)
power_management.can_suspend = false (bool)
power_management.can_suspend_hybrid = false (bool)
power_management.can_suspend_to_disk = false (bool)
power_management.can_suspend_to_ram = false (bool)
power_management.is_powersave_set = false (bool)
power_management.type = 'acpi' (string)
smbios.bios.release_date = '03/14/2006' (string)
smbios.bios.vendor = 'Phoenix Technologies Ltd.' (string)
smbios.bios.version = '2004Q3' (string)
smbios.chassis.manufacturer = 'TYAN Computer Corp' (string)
smbios.chassis.type = 'Main Server Chassis' (string)
smbios.system.manufacturer = 'TYAN Computer Corp' (string)
smbios.system.product = 'S2895' (string)
smbios.system.serial = '0123456789' (string)
smbios.system.uuid = 'Not Settable' (string)
smbios.system.version = 'TYAN Thunder K8WE S2895' (string)
system.chassis.manufacturer = 'TYAN Computer Corp' (string)
system.chassis.type = 'Main Server Chassis' (string)
system.firmware.release_date = '03/14/2006' (string)
system.firmware.vendor = 'Phoenix Technologies Ltd.' (string)
system.firmware.version = '2004Q3' (string)
system.formfactor = 'server' (string)
system.hardware.product = 'S2895' (string)
system.hardware.serial = '0123456789' (string)
system.hardware.uuid = 'Not Settable' (string)
system.hardware.vendor = 'TYAN Computer Corp' (string)
system.hardware.version = 'TYAN Thunder K8WE S2895' (string)
system.kernel.machine = 'x86_64' (string)
system.kernel.name = 'Linux' (string)
system.kernel.version = '2.6.22-gentoo-r9' (string)
system.product = 'S2895 TYAN Thunder K8WE S2895' (string)
system.vendor = 'TYAN Computer Corp' (string)
udi = '/org/freedesktop/Hal/devices/acpi_CPU0'
info.capabilities = {'processor'} (string list)
info.category = 'processor' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'AMD Opteron(tm) Processor 246' (string)
info.udi = '/org/freedesktop/Hal/devices/acpi_CPU0' (string)
linux.acpi_path = '/proc/acpi/processor/CPU0' (string)
linux.acpi_type = 1 (0x1) (int)
linux.hotplug_type = 4 (0x4) (int)
processor.can_throttle = false (bool)
processor.number = 0 (0x0) (int)
udi = '/org/freedesktop/Hal/devices/acpi_CPU1'
info.capabilities = {'processor'} (string list)
info.category = 'processor' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'AMD Opteron(tm) Processor 246' (string)
info.udi = '/org/freedesktop/Hal/devices/acpi_CPU1' (string)
linux.acpi_path = '/proc/acpi/processor/CPU1' (string)
linux.acpi_type = 1 (0x1) (int)
linux.hotplug_type = 4 (0x4) (int)
processor.can_throttle = false (bool)
processor.number = 1 (0x1) (int)
udi = '/org/freedesktop/Hal/devices/computer_alsa_timer'
alsa.device_file = '/dev/snd/timer' (string)
alsa.type = 'timer' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'ALSA Timer Device' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_alsa_timer' (string)
linux.device_file = '/dev/snd/timer' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/timer' (string)
udi = '/org/freedesktop/Hal/devices/computer_oss_sequencer_0'
info.capabilities = {'oss'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'OSS Sequencer Device' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_oss_sequencer_0' (string)
linux.device_file = '/dev/sound/sequencer2' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/sequencer2' (string)
oss.device_file = '/dev/sound/sequencer2' (string)
oss.type = 'sequencer' (string)
udi = '/org/freedesktop/Hal/devices/computer_oss_sequencer'
info.capabilities = {'oss'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'OSS Sequencer Device' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_oss_sequencer' (string)
linux.device_file = '/dev/sound/sequencer' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/sequencer' (string)
oss.device_file = '/dev/sound/sequencer' (string)
oss.type = 'sequencer' (string)
udi = '/org/freedesktop/Hal/devices/computer_alsa_sequencer'
alsa.device_file = '/dev/snd/seq' (string)
alsa.type = 'sequencer' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'ALSA Sequencer Device' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_alsa_sequencer' (string)
linux.device_file = '/dev/snd/seq' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/seq' (string)
udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_0'
button.has_state = false (bool)
button.type = 'power' (string)
info.addons = {'hald-addon-keyboard'} (string list)
info.capabilities = {'input', 'button'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Power Button (CM)' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_0' (string)
input.device = '/dev/input/event1' (string)
input.product = 'Power Button (CM)' (string)
linux.device_file = '/dev/input/event1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/class/input/input1/event1' (string)
udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input'
button.has_state = false (bool)
button.type = 'power' (string)
info.addons = {'hald-addon-keyboard'} (string list)
info.capabilities = {'input', 'button'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Power Button (FF)' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input' (string)
input.device = '/dev/input/event0' (string)
input.product = 'Power Button (FF)' (string)
linux.device_file = '/dev/input/event0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/class/input/input0/event0' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0a03_1'
info.bus = 'pnp' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'PCI Bus' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0a03_1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:0d' (string)
pnp.description = 'PCI Bus' (string)
pnp.id = 'PNP0a03' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0a03_0'
info.bus = 'pnp' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'PCI Bus' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0a03_0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:0c' (string)
pnp.description = 'PCI Bus' (string)
pnp.id = 'PNP0a03' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0f13'
info.bus = 'pnp' (string)
info.linux.driver = 'i8042 aux' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'PS/2 Port for PS/2-style Mice' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0f13' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:0b' (string)
pnp.description = 'PS/2 Port for PS/2-style Mice' (string)
pnp.id = 'PNP0f13' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0303'
info.bus = 'pnp' (string)
info.linux.driver = 'i8042 kbd' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'IBM Enhanced (101/102-key, PS/2 mouse support)' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0303' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:0a' (string)
pnp.description = 'IBM Enhanced (101/102-key, PS/2 mouse support)' (string)
pnp.id = 'PNP0303' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0700'
info.bus = 'pnp' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'PC standard floppy disk controller' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0700' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:09' (string)
pnp.description = 'PC standard floppy disk controller' (string)
pnp.id = 'PNP0700' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0501'
info.bus = 'pnp' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '16550A-compatible COM port' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0501' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:08' (string)
pnp.description = '16550A-compatible COM port' (string)
pnp.id = 'PNP0501' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0c04'
info.bus = 'pnp' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Math Coprocessor' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0c04' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:07' (string)
pnp.description = 'Math Coprocessor' (string)
pnp.id = 'PNP0c04' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0b00'
info.bus = 'pnp' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'AT Real-Time Clock' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0b00' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:06' (string)
pnp.description = 'AT Real-Time Clock' (string)
pnp.id = 'PNP0b00' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0800'
info.bus = 'pnp' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'AT-style speaker sound' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0800' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:05' (string)
pnp.description = 'AT-style speaker sound' (string)
pnp.id = 'PNP0800' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0200'
info.bus = 'pnp' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'AT DMA Controller' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0200' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:04' (string)
pnp.description = 'AT DMA Controller' (string)
pnp.id = 'PNP0200' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02_0'
info.bus = 'pnp' (string)
info.linux.driver = 'system' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02_0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:03' (string)
pnp.description = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)' (string)
pnp.id = 'PNP0c02' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02'
info.bus = 'pnp' (string)
info.linux.driver = 'system' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:02' (string)
pnp.description = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)' (string)
pnp.id = 'PNP0c02' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0a03'
info.bus = 'pnp' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'PCI Bus' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0a03' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:01' (string)
pnp.description = 'PCI Bus' (string)
pnp.id = 'PNP0a03' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0c01'
info.bus = 'pnp' (string)
info.linux.driver = 'system' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'System Board' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0c01' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:00' (string)
pnp.description = 'System Board' (string)
pnp.id = 'PNP0c01' (string)
udi = '/org/freedesktop/Hal/devices/platform_pcspkr'
info.bus = 'platform' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Platform Device (pcspkr)' (string)
info.subsystem = 'platform' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_pcspkr' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'platform' (string)
linux.sysfs_path = '/sys/devices/platform/pcspkr' (string)
platform.id = 'pcspkr' (string)
udi = '/org/freedesktop/Hal/devices/platform_i8042'
info.bus = 'platform' (string)
info.linux.driver = 'i8042' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Platform Device (i8042)' (string)
info.subsystem = 'platform' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_i8042' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'platform' (string)
linux.sysfs_path = '/sys/devices/platform/i8042' (string)
platform.id = 'i8042' (string)
udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port'
info.bus = 'serio' (string)
info.linux.driver = 'atkbd' (string)
info.parent = '/org/freedesktop/Hal/devices/platform_i8042' (string)
info.product = 'i8042 KBD port' (string)
info.subsystem = 'serio' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'serio' (string)
linux.sysfs_path = '/sys/devices/platform/i8042/serio0' (string)
serio.description = 'i8042 KBD port' (string)
serio.id = 'serio0' (string)
udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port_logicaldev_input'
info.addons = {'hald-addon-keyboard'} (string list)
info.capabilities = {'input', 'input.keyboard', 'button'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port' (string)
info.product = 'AT Translated Set 2 keyboard' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port_logicaldev_input' (string)
input.device = '/dev/input/event3' (string)
input.originating_device = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port' (string)
input.physical_device = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port' (string)
input.product = 'AT Translated Set 2 keyboard' (string)
linux.device_file = '/dev/input/event3' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/class/input/input3/event3' (string)
udi = '/org/freedesktop/Hal/devices/platform_floppy_0'
info.bus = 'platform' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Platform Device (floppy.0)' (string)
info.subsystem = 'platform' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_floppy_0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'platform' (string)
linux.sysfs_path = '/sys/devices/platform/floppy.0' (string)
platform.id = 'floppy.0' (string)
udi = '/org/freedesktop/Hal/devices/platform_floppy_0_storage'
block.device = '/dev/floppy/fd0' (string)
block.is_volume = false (bool)
block.major = 2 (0x2) (int)
block.minor = 0 (0x0) (int)
block.storage_device = '/org/freedesktop/Hal/devices/platform_floppy_0_storage' (string)
info.capabilities = {'storage', 'block'} (string list)
info.category = 'storage' (string)
info.interfaces = {'org.freedesktop.Hal.Device.Volume'} (string list)
info.parent = '/org/freedesktop/Hal/devices/platform_floppy_0' (string)
info.product = 'PC Floppy Drive' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_floppy_0_storage' (string)
info.vendor = '' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/block/fd0' (string)
org.freedesktop.Hal.Device.Volume.method_argnames = {'mount_point fstype extra_options', 'extra_options', 'extra_options'} (string list)
org.freedesktop.Hal.Device.Volume.method_execpaths = {'hal-storage-mount', 'hal-storage-unmount', 'hal-storage-eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_names = {'Mount', 'Unmount', 'Eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_signatures = {'ssas', 'as', 'as'} (string list)
storage.automount_enabled_hint = true (bool)
storage.bus = 'platform' (string)
storage.drive_type = 'floppy' (string)
storage.hotpluggable = false (bool)
storage.media_check_enabled = false (bool)
storage.model = '' (string)
storage.no_partitions_hint = true (bool)
storage.originating_device = '/org/freedesktop/Hal/devices/platform_floppy_0' (string)
storage.physical_device = '/org/freedesktop/Hal/devices/platform_floppy_0' (string)
storage.removable = true (bool)
storage.removable.media_available = false (bool)
storage.requires_eject = false (bool)
storage.size = 0 (0x0) (uint64)
storage.vendor = 'PC Floppy Drive' (string)
volume.mount.valid_options = {'ro', 'sync', 'dirsync', 'noatime', 'nodiratime', 'noexec', 'quiet', 'remount', 'exec', 'utf8', 'shortname=', 'codepage=', 'iocharset=', 'umask=', 'uid='} (string list)
udi = '/org/freedesktop/Hal/devices/pci_10de_5d_0'
info.bus = 'pci' (string)
info.linux.driver = 'pcieport-driver' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 PCIE Bridge' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_5d_0' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:80/0000:80:0e.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 4 (0x4) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:80/0000:80:0e.0' (string)
pci.product = 'CK804 PCIE Bridge' (string)
pci.product_id = 93 (0x5d) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_391_0'
info.bus = 'pci' (string)
info.linux.driver = 'nvidia' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_5d_0' (string)
info.product = 'G70 [GeForce 7600 GT]' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_391_0' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:80/0000:80:0e.0/0000:81:00.0' (string)
pci.device_class = 3 (0x3) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:80/0000:80:0e.0/0000:81:00.0' (string)
pci.product = 'G70 [GeForce 7600 GT]' (string)
pci.product_id = 913 (0x391) (int)
pci.subsys_product_id = 829 (0x33d) (int)
pci.subsys_vendor = 'nVidia Corporation' (string)
pci.subsys_vendor_id = 4318 (0x10de) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_57_0'
info.bus = 'pci' (string)
info.linux.driver = 'forcedeth' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 Ethernet Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_57_0' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:80/0000:80:0a.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 128 (0x80) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:80/0000:80:0a.0' (string)
pci.product = 'CK804 Ethernet Controller' (string)
pci.product_id = 87 (0x57) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/net_00_e0_81_54_b4_3f'
info.capabilities = {'net', 'net.80203'} (string list)
info.category = 'net.80203' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_57_0' (string)
info.product = 'Networking Interface' (string)
info.udi = '/org/freedesktop/Hal/devices/net_00_e0_81_54_b4_3f' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'net' (string)
linux.sysfs_path = '/sys/class/net/eth1' (string)
net.80203.mac_address = 964242486335 (0xe08154b43f) (uint64)
net.address = '00:e0:81:54:b4:3f' (string)
net.arp_proto_hw_id = 1 (0x1) (int)
net.interface = 'eth1' (string)
net.linux.ifindex = 3 (0x3) (int)
net.originating_device = '/org/freedesktop/Hal/devices/pci_10de_57_0' (string)
net.physical_device = '/org/freedesktop/Hal/devices/pci_10de_57_0' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_d3'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 Memory Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_d3' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:80/0000:80:01.0' (string)
pci.device_class = 5 (0x5) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 128 (0x80) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:80/0000:80:01.0' (string)
pci.product = 'CK804 Memory Controller' (string)
pci.product_id = 211 (0xd3) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_5e_0'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 Memory Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_5e_0' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:80/0000:80:00.0' (string)
pci.device_class = 5 (0x5) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 128 (0x80) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:80/0000:80:00.0' (string)
pci.product = 'CK804 Memory Controller' (string)
pci.product_id = 94 (0x5e) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_1022_7451_0'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'AMD-8131 PCI-X IOAPIC' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1022_7451_0' (string)
info.vendor = 'Advanced Micro Devices [AMD]' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0b.1' (string)
pci.device_class = 8 (0x8) (int)
pci.device_protocol = 16 (0x10) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0b.1' (string)
pci.product = 'AMD-8131 PCI-X IOAPIC' (string)
pci.product_id = 29777 (0x7451) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'Advanced Micro Devices [AMD]' (string)
pci.vendor_id = 4130 (0x1022) (int)
udi = '/org/freedesktop/Hal/devices/pci_1022_7450_0'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'AMD-8131 PCI-X Bridge' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1022_7450_0' (string)
info.vendor = 'Advanced Micro Devices [AMD]' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0b.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 4 (0x4) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0b.0' (string)
pci.product = 'AMD-8131 PCI-X Bridge' (string)
pci.product_id = 29776 (0x7450) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Advanced Micro Devices [AMD]' (string)
pci.vendor_id = 4130 (0x1022) (int)
udi = '/org/freedesktop/Hal/devices/pci_1022_7451'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'AMD-8131 PCI-X IOAPIC' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1022_7451' (string)
info.vendor = 'Advanced Micro Devices [AMD]' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0a.1' (string)
pci.device_class = 8 (0x8) (int)
pci.device_protocol = 16 (0x10) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0a.1' (string)
pci.product = 'AMD-8131 PCI-X IOAPIC' (string)
pci.product_id = 29777 (0x7451) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'Advanced Micro Devices [AMD]' (string)
pci.vendor_id = 4130 (0x1022) (int)
udi = '/org/freedesktop/Hal/devices/pci_1022_7450'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'AMD-8131 PCI-X Bridge' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1022_7450' (string)
info.vendor = 'Advanced Micro Devices [AMD]' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0a.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 4 (0x4) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0a.0' (string)
pci.product = 'AMD-8131 PCI-X Bridge' (string)
pci.product_id = 29776 (0x7450) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Advanced Micro Devices [AMD]' (string)
pci.vendor_id = 4130 (0x1022) (int)
udi = '/org/freedesktop/Hal/devices/pci_1102_4001'
info.bus = 'pci' (string)
info.linux.driver = 'ohci1394' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1022_7450' (string)
info.product = 'SB Audigy FireWire Port' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4001' (string)
info.vendor = 'Creative Labs' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0a.0/0000:09:04.2' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 16 (0x10) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0a.0/0000:09:04.2' (string)
pci.product = 'SB Audigy FireWire Port' (string)
pci.product_id = 16385 (0x4001) (int)
pci.subsys_product = 'SB Audigy FireWire Port' (string)
pci.subsys_product_id = 16 (0x10) (int)
pci.subsys_vendor = 'Creative Labs' (string)
pci.subsys_vendor_id = 4354 (0x1102) (int)
pci.vendor = 'Creative Labs' (string)
pci.vendor_id = 4354 (0x1102) (int)
udi = '/org/freedesktop/Hal/devices/pci_1102_7003'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1022_7450' (string)
info.product = 'SB Audigy Game Port' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_7003' (string)
info.vendor = 'Creative Labs' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0a.0/0000:09:04.1' (string)
pci.device_class = 9 (0x9) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 128 (0x80) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0a.0/0000:09:04.1' (string)
pci.product = 'SB Audigy Game Port' (string)
pci.product_id = 28675 (0x7003) (int)
pci.subsys_product = 'SB Audigy MIDI/Game Port' (string)
pci.subsys_product_id = 64 (0x40) (int)
pci.subsys_vendor = 'Creative Labs' (string)
pci.subsys_vendor_id = 4354 (0x1102) (int)
pci.vendor = 'Creative Labs' (string)
pci.vendor_id = 4354 (0x1102) (int)
udi = '/org/freedesktop/Hal/devices/pci_1102_4'
info.bus = 'pci' (string)
info.linux.driver = 'EMU10K1_Audigy' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1022_7450' (string)
info.product = 'SB Audigy' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.vendor = 'Creative Labs' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0a.0/0000:09:04.0' (string)
pci.device_class = 4 (0x4) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 1 (0x1) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:08/0000:08:0a.0/0000:09:04.0' (string)
pci.product = 'SB Audigy' (string)
pci.product_id = 4 (0x4) (int)
pci.subsys_product = 'SB Audigy 2 ZS (SB0350)' (string)
pci.subsys_product_id = 8194 (0x2002) (int)
pci.subsys_vendor = 'Creative Labs' (string)
pci.subsys_vendor_id = 4354 (0x1102) (int)
pci.vendor = 'Creative Labs' (string)
pci.vendor_id = 4354 (0x1102) (int)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_playback_4'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 4 (0x4) (int)
alsa.device_file = '/dev/snd/pcmC0D4p' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.pcm_class = 'generic' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'playback' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'ALSA Playback Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_playback_4' (string)
linux.device_file = '/dev/snd/pcmC0D4p' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/pcmC0D4p' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_capture_4'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 4 (0x4) (int)
alsa.device_file = '/dev/snd/pcmC0D4c' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.pcm_class = 'generic' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'capture' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'ALSA Capture Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_capture_4' (string)
linux.device_file = '/dev/snd/pcmC0D4c' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/pcmC0D4c' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_playback_3'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 3 (0x3) (int)
alsa.device_file = '/dev/snd/pcmC0D3p' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.pcm_class = 'generic' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'playback' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'ALSA Playback Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_playback_3' (string)
linux.device_file = '/dev/snd/pcmC0D3p' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/pcmC0D3p' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_playback_2'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 2 (0x2) (int)
alsa.device_file = '/dev/snd/pcmC0D2p' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.pcm_class = 'generic' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'playback' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'ALSA Playback Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_playback_2' (string)
linux.device_file = '/dev/snd/pcmC0D2p' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/pcmC0D2p' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_capture_2'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 2 (0x2) (int)
alsa.device_file = '/dev/snd/pcmC0D2c' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.pcm_class = 'generic' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'capture' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'ALSA Capture Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_capture_2' (string)
linux.device_file = '/dev/snd/pcmC0D2c' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/pcmC0D2c' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_capture_1'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 1 (0x1) (int)
alsa.device_file = '/dev/snd/pcmC0D1c' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.pcm_class = 'generic' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'capture' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'ALSA Capture Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_capture_1' (string)
linux.device_file = '/dev/snd/pcmC0D1c' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/pcmC0D1c' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_playback_0'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 0 (0x0) (int)
alsa.device_file = '/dev/snd/pcmC0D0p' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.pcm_class = 'generic' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'playback' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'ALSA Playback Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_playback_0' (string)
linux.device_file = '/dev/snd/pcmC0D0p' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/pcmC0D0p' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_capture_0'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 0 (0x0) (int)
alsa.device_file = '/dev/snd/pcmC0D0c' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.pcm_class = 'generic' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'capture' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'ALSA Capture Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_capture_0' (string)
linux.device_file = '/dev/snd/pcmC0D0c' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/pcmC0D0c' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_oss_mixer__1'
info.capabilities = {'oss'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) OSS Control Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_oss_mixer__1' (string)
linux.device_file = '/dev/sound/mixer' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/mixer' (string)
oss.card = 0 (0x0) (int)
oss.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
oss.device_file = '/dev/sound/mixer' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
oss.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
oss.type = 'mixer' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_midi_3'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 3 (0x3) (int)
alsa.device_file = '/dev/snd/midiC0D3' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'midi' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) ALSA MIDI Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_midi_3' (string)
linux.device_file = '/dev/snd/midiC0D3' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/midiC0D3' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_midi_2'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 2 (0x2) (int)
alsa.device_file = '/dev/snd/midiC0D2' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'midi' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) ALSA MIDI Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_midi_2' (string)
linux.device_file = '/dev/snd/midiC0D2' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/midiC0D2' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_midi_1'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 1 (0x1) (int)
alsa.device_file = '/dev/snd/midiC0D1' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'midi' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) ALSA MIDI Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_midi_1' (string)
linux.device_file = '/dev/snd/midiC0D1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/midiC0D1' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_midi_0'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 0 (0x0) (int)
alsa.device_file = '/dev/snd/midiC0D0' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'midi' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) ALSA MIDI Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_midi_0' (string)
linux.device_file = '/dev/snd/midiC0D0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/midiC0D0' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_oss_midi_0'
info.capabilities = {'oss'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) OSS MIDI Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_oss_midi_0' (string)
linux.device_file = '/dev/midi' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/midi' (string)
oss.card = 0 (0x0) (int)
oss.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
oss.device = 0 (0x0) (int)
oss.device_file = '/dev/midi' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
oss.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
oss.type = 'midi' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_hw_specific_2'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 2 (0x2) (int)
alsa.device_file = '/dev/snd/hwC0D2' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'hw_specific' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) ALSA hardware specific Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_hw_specific_2' (string)
linux.device_file = '/dev/snd/hwC0D2' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/hwC0D2' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_hw_specific_0'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device = 0 (0x0) (int)
alsa.device_file = '/dev/snd/hwC0D0' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'hw_specific' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) ALSA hardware specific Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_hw_specific_0' (string)
linux.device_file = '/dev/snd/hwC0D0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/hwC0D0' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_oss_pcm_0_0'
info.capabilities = {'oss'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) OSS PCM Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_oss_pcm_0_0' (string)
linux.device_file = '/dev/sound/dsp' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/dsp' (string)
oss.card = 0 (0x0) (int)
oss.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
oss.device = 0 (0x0) (int)
oss.device_file = '/dev/sound/dsp' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
oss.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
oss.type = 'pcm' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_control__1'
alsa.card = 0 (0x0) (int)
alsa.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
alsa.device_file = '/dev/snd/controlC0' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
alsa.type = 'control' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) ALSA Control Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_alsa_control__1' (string)
linux.device_file = '/dev/snd/controlC0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/controlC0' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_oss_pcm_0'
info.capabilities = {'oss'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) OSS PCM Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_oss_pcm_0' (string)
linux.device_file = '/dev/sound/audio' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/audio' (string)
oss.card = 0 (0x0) (int)
oss.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
oss.device = 0 (0x0) (int)
oss.device_file = '/dev/sound/audio' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
oss.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
oss.type = 'pcm' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_oss_midi_1'
info.capabilities = {'oss'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) OSS MIDI Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_oss_midi_1' (string)
linux.device_file = '/dev/amidi' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/amidi' (string)
oss.card = 0 (0x0) (int)
oss.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
oss.device = 1 (0x1) (int)
oss.device_file = '/dev/amidi' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
oss.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
oss.type = 'midi' (string)
udi = '/org/freedesktop/Hal/devices/pci_1102_4_oss_pcm_1'
info.capabilities = {'oss'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
info.product = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) OSS PCM Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1102_4_oss_pcm_1' (string)
linux.device_file = '/dev/sound/adsp' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/adsp' (string)
oss.card = 0 (0x0) (int)
oss.card_id = 'Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102)' (string)
oss.device = 1 (0x1) (int)
oss.device_file = '/dev/sound/adsp' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
oss.physical_device = '/org/freedesktop/Hal/devices/pci_1102_4' (string)
oss.type = 'pcm' (string)
udi = '/org/freedesktop/Hal/devices/pci_1022_1103_0'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'K8 [Athlon64/Opteron] Miscellaneous Control' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1022_1103_0' (string)
info.vendor = 'Advanced Micro Devices [AMD]' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:19.3' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:19.3' (string)
pci.product = 'K8 [Athlon64/Opteron] Miscellaneous Control' (string)
pci.product_id = 4355 (0x1103) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Advanced Micro Devices [AMD]' (string)
pci.vendor_id = 4130 (0x1022) (int)
udi = '/org/freedesktop/Hal/devices/pci_1022_1102_0'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'K8 [Athlon64/Opteron] DRAM Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1022_1102_0' (string)
info.vendor = 'Advanced Micro Devices [AMD]' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:19.2' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:19.2' (string)
pci.product = 'K8 [Athlon64/Opteron] DRAM Controller' (string)
pci.product_id = 4354 (0x1102) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Advanced Micro Devices [AMD]' (string)
pci.vendor_id = 4130 (0x1022) (int)
udi = '/org/freedesktop/Hal/devices/pci_1022_1101_0'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'K8 [Athlon64/Opteron] Address Map' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1022_1101_0' (string)
info.vendor = 'Advanced Micro Devices [AMD]' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:19.1' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:19.1' (string)
pci.product = 'K8 [Athlon64/Opteron] Address Map' (string)
pci.product_id = 4353 (0x1101) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Advanced Micro Devices [AMD]' (string)
pci.vendor_id = 4130 (0x1022) (int)
udi = '/org/freedesktop/Hal/devices/pci_1022_1100_0'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'K8 [Athlon64/Opteron] HyperTransport Technology Configuration' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1022_1100_0' (string)
info.vendor = 'Advanced Micro Devices [AMD]' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:19.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:19.0' (string)
pci.product = 'K8 [Athlon64/Opteron] HyperTransport Technology Configuration' (string)
pci.product_id = 4352 (0x1100) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Advanced Micro Devices [AMD]' (string)
pci.vendor_id = 4130 (0x1022) (int)
udi = '/org/freedesktop/Hal/devices/pci_1022_1103'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'K8 [Athlon64/Opteron] Miscellaneous Control' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1022_1103' (string)
info.vendor = 'Advanced Micro Devices [AMD]' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:18.3' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:18.3' (string)
pci.product = 'K8 [Athlon64/Opteron] Miscellaneous Control' (string)
pci.product_id = 4355 (0x1103) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Advanced Micro Devices [AMD]' (string)
pci.vendor_id = 4130 (0x1022) (int)
udi = '/org/freedesktop/Hal/devices/pci_1022_1102'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'K8 [Athlon64/Opteron] DRAM Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1022_1102' (string)
info.vendor = 'Advanced Micro Devices [AMD]' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:18.2' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:18.2' (string)
pci.product = 'K8 [Athlon64/Opteron] DRAM Controller' (string)
pci.product_id = 4354 (0x1102) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Advanced Micro Devices [AMD]' (string)
pci.vendor_id = 4130 (0x1022) (int)
udi = '/org/freedesktop/Hal/devices/pci_1022_1101'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'K8 [Athlon64/Opteron] Address Map' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1022_1101' (string)
info.vendor = 'Advanced Micro Devices [AMD]' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:18.1' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:18.1' (string)
pci.product = 'K8 [Athlon64/Opteron] Address Map' (string)
pci.product_id = 4353 (0x1101) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Advanced Micro Devices [AMD]' (string)
pci.vendor_id = 4130 (0x1022) (int)
udi = '/org/freedesktop/Hal/devices/pci_1022_1100'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'K8 [Athlon64/Opteron] HyperTransport Technology Configuration' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1022_1100' (string)
info.vendor = 'Advanced Micro Devices [AMD]' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:18.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:18.0' (string)
pci.product = 'K8 [Athlon64/Opteron] HyperTransport Technology Configuration' (string)
pci.product_id = 4352 (0x1100) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Advanced Micro Devices [AMD]' (string)
pci.vendor_id = 4130 (0x1022) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_5d'
info.bus = 'pci' (string)
info.linux.driver = 'pcieport-driver' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 PCIE Bridge' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_5d' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:0e.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 4 (0x4) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:0e.0' (string)
pci.product = 'CK804 PCIE Bridge' (string)
pci.product_id = 93 (0x5d) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_391'
info.bus = 'pci' (string)
info.linux.driver = 'nvidia' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_5d' (string)
info.product = 'G70 [GeForce 7600 GT]' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_391' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:0e.0/0000:02:00.0' (string)
pci.device_class = 3 (0x3) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:0e.0/0000:02:00.0' (string)
pci.product = 'G70 [GeForce 7600 GT]' (string)
pci.product_id = 913 (0x391) (int)
pci.subsys_product_id = 829 (0x33d) (int)
pci.subsys_vendor = 'nVidia Corporation' (string)
pci.subsys_vendor_id = 4318 (0x10de) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_57'
info.bus = 'pci' (string)
info.linux.driver = 'forcedeth' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 Ethernet Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_57' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:0a.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 128 (0x80) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:0a.0' (string)
pci.product = 'CK804 Ethernet Controller' (string)
pci.product_id = 87 (0x57) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/net_00_e0_81_54_b4_3e'
info.capabilities = {'net', 'net.80203'} (string list)
info.category = 'net.80203' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_57' (string)
info.product = 'Networking Interface' (string)
info.udi = '/org/freedesktop/Hal/devices/net_00_e0_81_54_b4_3e' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'net' (string)
linux.sysfs_path = '/sys/class/net/eth0' (string)
net.80203.mac_address = 964242486334 (0xe08154b43e) (uint64)
net.address = '00:e0:81:54:b4:3e' (string)
net.arp_proto_hw_id = 1 (0x1) (int)
net.interface = 'eth0' (string)
net.linux.ifindex = 2 (0x2) (int)
net.originating_device = '/org/freedesktop/Hal/devices/pci_10de_57' (string)
net.physical_device = '/org/freedesktop/Hal/devices/pci_10de_57' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_5c'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 PCI Bridge' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_5c' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:09.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 1 (0x1) (int)
pci.device_subclass = 4 (0x4) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:09.0' (string)
pci.product = 'CK804 PCI Bridge' (string)
pci.product_id = 92 (0x5c) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_104c_8023'
info.bus = 'pci' (string)
info.linux.driver = 'ohci1394' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_5c' (string)
info.product = 'TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_104c_8023' (string)
info.vendor = 'Texas Instruments' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:09.0/0000:01:05.0' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 16 (0x10) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:09.0/0000:01:05.0' (string)
pci.product = 'TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)' (string)
pci.product_id = 32803 (0x8023) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'Texas Instruments' (string)
pci.vendor_id = 4172 (0x104c) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_55'
info.bus = 'pci' (string)
info.linux.driver = 'sata_nv' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 Serial ATA Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_55' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:08.0' (string)
pci.device_class = 1 (0x1) (int)
pci.device_protocol = 133 (0x85) (int)
pci.device_subclass = 1 (0x1) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:08.0' (string)
pci.product = 'CK804 Serial ATA Controller' (string)
pci.product_id = 85 (0x55) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_55_scsi_host'
info.capabilities = {'scsi_host'} (string list)
info.category = 'scsi_host' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_55' (string)
info.product = 'SCSI Host Adapter' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_55_scsi_host' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_host' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:08.0/host3' (string)
scsi_host.host = 3 (0x3) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_55_scsi_host_scsi_device_lun0'
info.bus = 'scsi' (string)
info.linux.driver = 'sd' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_55_scsi_host' (string)
info.product = 'SCSI Device' (string)
info.subsystem = 'scsi' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_55_scsi_host_scsi_device_lun0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:08.0/host3/target3:0:0/3:0:0:0' (string)
scsi.bus = 0 (0x0) (int)
scsi.host = 3 (0x3) (int)
scsi.lun = 0 (0x0) (int)
scsi.model = 'ST3250824AS' (string)
scsi.target = 0 (0x0) (int)
scsi.type = 'disk' (string)
scsi.vendor = 'ATA' (string)
udi = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250824AS_4ND3HZYS'
block.device = '/dev/sdb' (string)
block.is_volume = false (bool)
block.major = 8 (0x8) (int)
block.minor = 16 (0x10) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250824AS_4ND3HZYS' (string)
info.capabilities = {'storage', 'block'} (string list)
info.category = 'storage' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_55_scsi_host_scsi_device_lun0' (string)
info.product = 'ST3250824AS' (string)
info.udi = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250824AS_4ND3HZYS' (string)
info.vendor = 'ATA' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/block/sdb' (string)
storage.automount_enabled_hint = true (bool)
storage.bus = 'scsi' (string)
storage.drive_type = 'disk' (string)
storage.firmware_version = '3.AA' (string)
storage.hotpluggable = false (bool)
storage.lun = 0 (0x0) (int)
storage.media_check_enabled = false (bool)
storage.model = 'ST3250824AS' (string)
storage.no_partitions_hint = false (bool)
storage.originating_device = '/org/freedesktop/Hal/devices/pci_10de_55_scsi_host_scsi_device_lun0' (string)
storage.partitioning_scheme = 'mbr' (string)
storage.physical_device = '/org/freedesktop/Hal/devices/pci_10de_55_scsi_host_scsi_device_lun0' (string)
storage.removable = false (bool)
storage.removable.media_available = true (bool)
storage.removable.media_size = 250059350016 (0x3a38b2e000) (uint64)
storage.requires_eject = false (bool)
storage.serial = 'SATA_ST3250824AS_4ND3HZYS' (string)
storage.size = 250059350016 (0x3a38b2e000) (uint64)
storage.vendor = 'ATA' (string)
udi = '/org/freedesktop/Hal/devices/volume_uuid_cfdffbef_aed294ac_3dfc7c93_2ceb5a03_0'
block.device = '/dev/sdb3' (string)
block.is_volume = true (bool)
block.major = 8 (0x8) (int)
block.minor = 19 (0x13) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250824AS_4ND3HZYS' (string)
info.capabilities = {'volume', 'block'} (string list)
info.category = 'volume' (string)
info.parent = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250824AS_4ND3HZYS' (string)
info.product = 'Volume (linux_raid_member)' (string)
info.udi = '/org/freedesktop/Hal/devices/volume_uuid_cfdffbef_aed294ac_3dfc7c93_2ceb5a03_0' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/block/sdb/sdb3' (string)
storage.model = '' (string)
volume.block_size = 512 (0x200) (int)
volume.fstype = 'linux_raid_member' (string)
volume.fsusage = 'raid' (string)
volume.fsversion = '0.90.0' (string)
volume.is_disc = false (bool)
volume.is_mounted = false (bool)
volume.is_mounted_read_only = false (bool)
volume.is_partition = true (bool)
volume.label = '' (string)
volume.linux.is_device_mapper = false (bool)
volume.mount_point = '' (string)
volume.num_blocks = 244204065 (0xe8e4221) (int)
volume.partition.flags = {} (string list)
volume.partition.label = '' (string)
volume.partition.media_size = 250059350016 (0x3a38b2e000) (uint64)
volume.partition.number = 3 (0x3) (int)
volume.partition.scheme = 'mbr' (string)
volume.partition.start = 125024256000 (0x1d1c06c000) (uint64)
volume.partition.type = '0xfd' (string)
volume.partition.uuid = '' (string)
volume.size = 125032481280 (0x1d1c844200) (uint64)
volume.uuid = 'cfdffbef:aed294ac:3dfc7c93:2ceb5a03' (string)
udi = '/org/freedesktop/Hal/devices/volume_uuid_31f75a41_fd25_4ea0_bfd4_d3bd6c19d507'
block.device = '/dev/sdb1' (string)
block.is_volume = true (bool)
block.major = 8 (0x8) (int)
block.minor = 17 (0x11) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250824AS_4ND3HZYS' (string)
info.capabilities = {'volume', 'block'} (string list)
info.category = 'volume' (string)
info.interfaces = {'org.freedesktop.Hal.Device.Volume'} (string list)
info.parent = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250824AS_4ND3HZYS' (string)
info.product = 'Volume (ext2)' (string)
info.udi = '/org/freedesktop/Hal/devices/volume_uuid_31f75a41_fd25_4ea0_bfd4_d3bd6c19d507' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/block/sdb/sdb1' (string)
org.freedesktop.Hal.Device.Volume.method_argnames = {'mount_point fstype extra_options', 'extra_options', 'extra_options'} (string list)
org.freedesktop.Hal.Device.Volume.method_execpaths = {'hal-storage-mount', 'hal-storage-unmount', 'hal-storage-eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_names = {'Mount', 'Unmount', 'Eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_signatures = {'ssas', 'as', 'as'} (string list)
storage.model = '' (string)
volume.block_size = 512 (0x200) (int)
volume.fstype = 'ext2' (string)
volume.fsusage = 'filesystem' (string)
volume.fsversion = '1.0' (string)
volume.ignore = false (bool)
volume.is_disc = false (bool)
volume.is_mounted = false (bool)
volume.is_mounted_read_only = false (bool)
volume.is_partition = true (bool)
volume.label = '' (string)
volume.linux.is_device_mapper = false (bool)
volume.mount.valid_options = {'ro', 'sync', 'dirsync', 'noatime', 'nodiratime', 'noexec', 'quiet', 'remount', 'exec'} (string list)
volume.mount_point = '' (string)
volume.num_blocks = 244187937 (0xe8e0321) (int)
volume.partition.flags = {} (string list)
volume.partition.label = '' (string)
volume.partition.media_size = 250059350016 (0x3a38b2e000) (uint64)
volume.partition.number = 1 (0x1) (int)
volume.partition.scheme = 'mbr' (string)
volume.partition.start = 32256 (0x7e00) (uint64)
volume.partition.type = '0x83' (string)
volume.partition.uuid = '' (string)
volume.size = 125024223744 (0x1d1c064200) (uint64)
volume.unmount.valid_options = {'lazy'} (string list)
volume.uuid = '31f75a41-fd25-4ea0-bfd4-d3bd6c19d507' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_55_scsi_host_scsi_device_lun0_scsi_generic'
info.capabilities = {'scsi_generic'} (string list)
info.category = 'scsi_generic' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_55_scsi_host_scsi_device_lun0' (string)
info.product = 'SCSI Generic Interface' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_55_scsi_host_scsi_device_lun0_scsi_generic' (string)
linux.device_file = '/dev/sg1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_generic' (string)
linux.sysfs_path = '/sys/class/scsi_generic/sg1' (string)
scsi_generic.device = '/dev/sg1' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_54'
info.bus = 'pci' (string)
info.linux.driver = 'sata_nv' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 Serial ATA Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_54' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:07.0' (string)
pci.device_class = 1 (0x1) (int)
pci.device_protocol = 133 (0x85) (int)
pci.device_subclass = 1 (0x1) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:07.0' (string)
pci.product = 'CK804 Serial ATA Controller' (string)
pci.product_id = 84 (0x54) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_54_scsi_host'
info.capabilities = {'scsi_host'} (string list)
info.category = 'scsi_host' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_54' (string)
info.product = 'SCSI Host Adapter' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_54_scsi_host' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_host' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:07.0/host0' (string)
scsi_host.host = 0 (0x0) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_54_scsi_host_scsi_device_lun0'
info.bus = 'scsi' (string)
info.linux.driver = 'sd' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_54_scsi_host' (string)
info.product = 'SCSI Device' (string)
info.subsystem = 'scsi' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_54_scsi_host_scsi_device_lun0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:07.0/host0/target0:0:0/0:0:0:0' (string)
scsi.bus = 0 (0x0) (int)
scsi.host = 0 (0x0) (int)
scsi.lun = 0 (0x0) (int)
scsi.model = 'ST3250823AS' (string)
scsi.target = 0 (0x0) (int)
scsi.type = 'disk' (string)
scsi.vendor = 'ATA' (string)
udi = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250823AS_3ND0SEDJ'
block.device = '/dev/sda' (string)
block.is_volume = false (bool)
block.major = 8 (0x8) (int)
block.minor = 0 (0x0) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250823AS_3ND0SEDJ' (string)
info.capabilities = {'storage', 'block'} (string list)
info.category = 'storage' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_54_scsi_host_scsi_device_lun0' (string)
info.product = 'ST3250823AS' (string)
info.udi = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250823AS_3ND0SEDJ' (string)
info.vendor = 'ATA' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/block/sda' (string)
storage.automount_enabled_hint = true (bool)
storage.bus = 'scsi' (string)
storage.drive_type = 'disk' (string)
storage.firmware_version = '3.02' (string)
storage.hotpluggable = false (bool)
storage.lun = 0 (0x0) (int)
storage.media_check_enabled = false (bool)
storage.model = 'ST3250823AS' (string)
storage.no_partitions_hint = false (bool)
storage.originating_device = '/org/freedesktop/Hal/devices/pci_10de_54_scsi_host_scsi_device_lun0' (string)
storage.partitioning_scheme = 'mbr' (string)
storage.physical_device = '/org/freedesktop/Hal/devices/pci_10de_54_scsi_host_scsi_device_lun0' (string)
storage.removable = false (bool)
storage.removable.media_available = true (bool)
storage.removable.media_size = 250059350016 (0x3a38b2e000) (uint64)
storage.requires_eject = false (bool)
storage.serial = 'SATA_ST3250823AS_3ND0SEDJ' (string)
storage.size = 250059350016 (0x3a38b2e000) (uint64)
storage.vendor = 'ATA' (string)
udi = '/org/freedesktop/Hal/devices/volume_uuid_cfdffbef_aed294ac_3dfc7c93_2ceb5a03'
block.device = '/dev/sda3' (string)
block.is_volume = true (bool)
block.major = 8 (0x8) (int)
block.minor = 3 (0x3) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250823AS_3ND0SEDJ' (string)
info.capabilities = {'volume', 'block'} (string list)
info.category = 'volume' (string)
info.parent = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250823AS_3ND0SEDJ' (string)
info.product = 'Volume (linux_raid_member)' (string)
info.udi = '/org/freedesktop/Hal/devices/volume_uuid_cfdffbef_aed294ac_3dfc7c93_2ceb5a03' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/block/sda/sda3' (string)
storage.model = '' (string)
volume.block_size = 512 (0x200) (int)
volume.fstype = 'linux_raid_member' (string)
volume.fsusage = 'raid' (string)
volume.fsversion = '0.90.0' (string)
volume.is_disc = false (bool)
volume.is_mounted = false (bool)
volume.is_mounted_read_only = false (bool)
volume.is_partition = true (bool)
volume.label = '' (string)
volume.linux.is_device_mapper = false (bool)
volume.mount_point = '' (string)
volume.num_blocks = 244204065 (0xe8e4221) (int)
volume.partition.flags = {} (string list)
volume.partition.label = '' (string)
volume.partition.media_size = 250059350016 (0x3a38b2e000) (uint64)
volume.partition.number = 3 (0x3) (int)
volume.partition.scheme = 'mbr' (string)
volume.partition.start = 125024256000 (0x1d1c06c000) (uint64)
volume.partition.type = '0xfd' (string)
volume.partition.uuid = '' (string)
volume.size = 125032481280 (0x1d1c844200) (uint64)
volume.uuid = 'cfdffbef:aed294ac:3dfc7c93:2ceb5a03' (string)
udi = '/org/freedesktop/Hal/devices/volume_uuid_aea60371_7167_465f_b08e_eeb9fe0fe133'
block.device = '/dev/sda2' (string)
block.is_volume = true (bool)
block.major = 8 (0x8) (int)
block.minor = 2 (0x2) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250823AS_3ND0SEDJ' (string)
info.capabilities = {'volume', 'block'} (string list)
info.category = 'volume' (string)
info.interfaces = {'org.freedesktop.Hal.Device.Volume'} (string list)
info.parent = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250823AS_3ND0SEDJ' (string)
info.product = 'Volume (ext3)' (string)
info.udi = '/org/freedesktop/Hal/devices/volume_uuid_aea60371_7167_465f_b08e_eeb9fe0fe133' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/block/sda/sda2' (string)
org.freedesktop.Hal.Device.Volume.method_argnames = {'mount_point fstype extra_options', 'extra_options', 'extra_options'} (string list)
org.freedesktop.Hal.Device.Volume.method_execpaths = {'hal-storage-mount', 'hal-storage-unmount', 'hal-storage-eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_names = {'Mount', 'Unmount', 'Eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_signatures = {'ssas', 'as', 'as'} (string list)
storage.model = '' (string)
volume.block_size = 512 (0x200) (int)
volume.fstype = 'ext3' (string)
volume.fsusage = 'filesystem' (string)
volume.fsversion = '1.0' (string)
volume.ignore = true (bool)
volume.is_disc = false (bool)
volume.is_mounted = true (bool)
volume.is_mounted_read_only = false (bool)
volume.is_partition = true (bool)
volume.label = '' (string)
volume.linux.is_device_mapper = false (bool)
volume.mount.valid_options = {'ro', 'sync', 'dirsync', 'noatime', 'nodiratime', 'noexec', 'quiet', 'remount', 'exec', 'acl', 'user_xattr', 'data='} (string list)
volume.mount_point = '/' (string)
volume.num_blocks = 244011285 (0xe8b5115) (int)
volume.partition.flags = {} (string list)
volume.partition.label = '' (string)
volume.partition.media_size = 250059350016 (0x3a38b2e000) (uint64)
volume.partition.number = 2 (0x2) (int)
volume.partition.scheme = 'mbr' (string)
volume.partition.start = 90478080 (0x5649600) (uint64)
volume.partition.type = '0x83' (string)
volume.partition.uuid = '' (string)
volume.size = 124933777920 (0x1d16a22a00) (uint64)
volume.unmount.valid_options = {'lazy'} (string list)
volume.uuid = 'aea60371-7167-465f-b08e-eeb9fe0fe133' (string)
udi = '/org/freedesktop/Hal/devices/volume_uuid_594ad0fd_ae8a_441f_bc0b_a7abf4b8e687'
block.device = '/dev/sda1' (string)
block.is_volume = true (bool)
block.major = 8 (0x8) (int)
block.minor = 1 (0x1) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250823AS_3ND0SEDJ' (string)
info.capabilities = {'volume', 'block'} (string list)
info.category = 'volume' (string)
info.interfaces = {'org.freedesktop.Hal.Device.Volume'} (string list)
info.parent = '/org/freedesktop/Hal/devices/storage_serial_SATA_ST3250823AS_3ND0SEDJ' (string)
info.product = 'Volume (ext2)' (string)
info.udi = '/org/freedesktop/Hal/devices/volume_uuid_594ad0fd_ae8a_441f_bc0b_a7abf4b8e687' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/block/sda/sda1' (string)
org.freedesktop.Hal.Device.Volume.method_argnames = {'mount_point fstype extra_options', 'extra_options', 'extra_options'} (string list)
org.freedesktop.Hal.Device.Volume.method_execpaths = {'hal-storage-mount', 'hal-storage-unmount', 'hal-storage-eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_names = {'Mount', 'Unmount', 'Eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_signatures = {'ssas', 'as', 'as'} (string list)
storage.model = '' (string)
volume.block_size = 512 (0x200) (int)
volume.fstype = 'ext2' (string)
volume.fsusage = 'filesystem' (string)
volume.fsversion = '1.0' (string)
volume.ignore = false (bool)
volume.is_disc = false (bool)
volume.is_mounted = false (bool)
volume.is_mounted_read_only = false (bool)
volume.is_partition = true (bool)
volume.label = '' (string)
volume.linux.is_device_mapper = false (bool)
volume.mount.valid_options = {'ro', 'sync', 'dirsync', 'noatime', 'nodiratime', 'noexec', 'quiet', 'remount', 'exec'} (string list)
volume.mount_point = '' (string)
volume.num_blocks = 176652 (0x2b20c) (int)
volume.partition.flags = {'boot'} (string list)
volume.partition.label = '' (string)
volume.partition.media_size = 250059350016 (0x3a38b2e000) (uint64)
volume.partition.number = 1 (0x1) (int)
volume.partition.scheme = 'mbr' (string)
volume.partition.start = 32256 (0x7e00) (uint64)
volume.partition.type = '0x83' (string)
volume.partition.uuid = '' (string)
volume.size = 90445824 (0x5641800) (uint64)
volume.unmount.valid_options = {'lazy'} (string list)
volume.uuid = '594ad0fd-ae8a-441f-bc0b-a7abf4b8e687' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_54_scsi_host_scsi_device_lun0_scsi_generic'
info.capabilities = {'scsi_generic'} (string list)
info.category = 'scsi_generic' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_54_scsi_host_scsi_device_lun0' (string)
info.product = 'SCSI Generic Interface' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_54_scsi_host_scsi_device_lun0_scsi_generic' (string)
linux.device_file = '/dev/sg0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_generic' (string)
linux.sysfs_path = '/sys/class/scsi_generic/sg0' (string)
scsi_generic.device = '/dev/sg0' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_53'
info.bus = 'pci' (string)
info.linux.driver = 'AMD_IDE' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 IDE' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_53' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:06.0' (string)
pci.device_class = 1 (0x1) (int)
pci.device_protocol = 138 (0x8a) (int)
pci.device_subclass = 1 (0x1) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:06.0' (string)
pci.product = 'CK804 IDE' (string)
pci.product_id = 83 (0x53) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_53_ide_0_0'
ide.channel = 0 (0x0) (int)
ide.host = 0 (0x0) (int)
info.bus = 'ide' (string)
info.linux.driver = 'ide-cdrom' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_53' (string)
info.product = 'IDE device (master)' (string)
info.subsystem = 'ide' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_53_ide_0_0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'ide' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:06.0/ide0/0.0' (string)
udi = '/org/freedesktop/Hal/devices/storage_model_TOSHIBA_CDWDVD_SD_R1612'
block.device = '/dev/hda' (string)
block.is_volume = false (bool)
block.major = 3 (0x3) (int)
block.minor = 0 (0x0) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_model_TOSHIBA_CDWDVD_SD_R1612' (string)
info.capabilities = {'storage', 'block'} (string list)
info.category = 'storage' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_53_ide_0_0' (string)
info.udi = '/org/freedesktop/Hal/devices/storage_model_TOSHIBA_CDWDVD_SD_R1612' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/block/hda' (string)
storage.automount_enabled_hint = true (bool)
storage.bus = 'ide' (string)
storage.drive_type = 'disk' (string)
storage.firmware_version = 'TB01' (string)
storage.hotpluggable = false (bool)
storage.media_check_enabled = false (bool)
storage.model = 'TOSHIBA_CDWDVD_SD-R1612' (string)
storage.no_partitions_hint = false (bool)
storage.originating_device = '/org/freedesktop/Hal/devices/pci_10de_53_ide_0_0' (string)
storage.physical_device = '/org/freedesktop/Hal/devices/pci_10de_53_ide_0_0' (string)
storage.removable = true (bool)
storage.removable.media_available = false (bool)
storage.requires_eject = false (bool)
storage.size = 0 (0x0) (uint64)
storage.vendor = '' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_59'
info.bus = 'pci' (string)
info.linux.driver = 'Intel ICH' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 AC'97 Audio Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:04.0' (string)
pci.device_class = 4 (0x4) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 1 (0x1) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:04.0' (string)
pci.product = 'CK804 AC'97 Audio Controller' (string)
pci.product_id = 89 (0x59) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_59_alsa_playback_2'
alsa.card = 1 (0x1) (int)
alsa.card_id = 'NVidia CK804 with AD1981B' (string)
alsa.device = 2 (0x2) (int)
alsa.device_file = '/dev/snd/pcmC1D2p' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
alsa.pcm_class = 'generic' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
alsa.type = 'playback' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
info.product = 'ALSA Playback Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_59_alsa_playback_2' (string)
linux.device_file = '/dev/snd/pcmC1D2p' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/pcmC1D2p' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_59_alsa_capture_1'
alsa.card = 1 (0x1) (int)
alsa.card_id = 'NVidia CK804 with AD1981B' (string)
alsa.device = 1 (0x1) (int)
alsa.device_file = '/dev/snd/pcmC1D1c' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
alsa.pcm_class = 'generic' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
alsa.type = 'capture' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
info.product = 'ALSA Capture Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_59_alsa_capture_1' (string)
linux.device_file = '/dev/snd/pcmC1D1c' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/pcmC1D1c' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_59_alsa_playback_0'
alsa.card = 1 (0x1) (int)
alsa.card_id = 'NVidia CK804 with AD1981B' (string)
alsa.device = 0 (0x0) (int)
alsa.device_file = '/dev/snd/pcmC1D0p' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
alsa.pcm_class = 'generic' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
alsa.type = 'playback' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
info.product = 'ALSA Playback Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_59_alsa_playback_0' (string)
linux.device_file = '/dev/snd/pcmC1D0p' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/pcmC1D0p' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_59_alsa_capture_0'
alsa.card = 1 (0x1) (int)
alsa.card_id = 'NVidia CK804 with AD1981B' (string)
alsa.device = 0 (0x0) (int)
alsa.device_file = '/dev/snd/pcmC1D0c' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
alsa.pcm_class = 'generic' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
alsa.type = 'capture' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
info.product = 'ALSA Capture Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_59_alsa_capture_0' (string)
linux.device_file = '/dev/snd/pcmC1D0c' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/pcmC1D0c' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_59_oss_mixer__1'
info.capabilities = {'oss'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
info.product = 'NVidia CK804 with AD1981B OSS Control Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_59_oss_mixer__1' (string)
linux.device_file = '/dev/sound/mixer1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/mixer1' (string)
oss.card = 1 (0x1) (int)
oss.card_id = 'NVidia CK804 with AD1981B' (string)
oss.device_file = '/dev/sound/mixer1' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
oss.physical_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
oss.type = 'mixer' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_59_oss_pcm_0_0'
info.capabilities = {'oss'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
info.product = 'NVidia CK804 with AD1981B OSS PCM Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_59_oss_pcm_0_0' (string)
linux.device_file = '/dev/sound/dsp1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/dsp1' (string)
oss.card = 1 (0x1) (int)
oss.card_id = 'NVidia CK804 with AD1981B' (string)
oss.device = 0 (0x0) (int)
oss.device_file = '/dev/sound/dsp1' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
oss.physical_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
oss.type = 'pcm' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_59_alsa_control__1'
alsa.card = 1 (0x1) (int)
alsa.card_id = 'NVidia CK804 with AD1981B' (string)
alsa.device_file = '/dev/snd/controlC1' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
alsa.physical_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
alsa.type = 'control' (string)
info.capabilities = {'alsa'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
info.product = 'NVidia CK804 with AD1981B ALSA Control Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_59_alsa_control__1' (string)
linux.device_file = '/dev/snd/controlC1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/controlC1' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_59_oss_pcm_0'
info.capabilities = {'oss'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
info.product = 'NVidia CK804 with AD1981B OSS PCM Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_59_oss_pcm_0' (string)
linux.device_file = '/dev/sound/audio1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/audio1' (string)
oss.card = 1 (0x1) (int)
oss.card_id = 'NVidia CK804 with AD1981B' (string)
oss.device = 0 (0x0) (int)
oss.device_file = '/dev/sound/audio1' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
oss.physical_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
oss.type = 'pcm' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_59_oss_pcm_1'
info.capabilities = {'oss'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
info.product = 'NVidia CK804 with AD1981B OSS PCM Device' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_59_oss_pcm_1' (string)
linux.device_file = '/dev/sound/adsp1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/class/sound/adsp1' (string)
oss.card = 1 (0x1) (int)
oss.card_id = 'NVidia CK804 with AD1981B' (string)
oss.device = 1 (0x1) (int)
oss.device_file = '/dev/sound/adsp1' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
oss.physical_device = '/org/freedesktop/Hal/devices/pci_10de_59' (string)
oss.type = 'pcm' (string)
udi = '/org/freedesktop/Hal/devices/pci_10de_5b'
info.bus = 'pci' (string)
info.linux.driver = 'ehci_hcd' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 USB Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_5b' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 32 (0x20) (int)
pci.device_subclass = 3 (0x3) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1' (string)
pci.product = 'CK804 USB Controller' (string)
pci.product_id = 91 (0x5b) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_1'
info.bus = 'usb_device' (string)
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_5b' (string)
info.product = 'EHCI Host Controller' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_1' (string)
info.vendor = 'Linux 2.6.22-gentoo-r9 ehci_hcd' (string)
linux.device_file = '/dev/bus/usb/001/001' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1/usb1' (string)
usb_device.bus_number = 1 (0x1) (int)
usb_device.can_wake_up = true (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 9 (0x9) (int)
usb_device.device_protocol = 1 (0x1) (int)
usb_device.device_revision_bcd = 518 (0x206) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = true (bool)
usb_device.linux.device_number = 1 (0x1) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1/usb1' (string)
usb_device.max_power = 0 (0x0) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 10 (0xa) (int)
usb_device.product = 'EHCI Host Controller' (string)
usb_device.product_id = 0 (0x0) (int)
usb_device.serial = '0000:00:02.1' (string)
usb_device.speed = 480.0 (480) (double)
usb_device.speed_bcd = 294912 (0x48000) (int)
usb_device.vendor = 'Linux 2.6.22-gentoo-r9 ehci_hcd' (string)
usb_device.vendor_id = 0 (0x0) (int)
usb_device.version = 2.0 (2) (double)
usb_device.version_bcd = 512 (0x200) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047'
info.bus = 'usb_device' (string)
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_1' (string)
info.product = 'USB 2.0 Card Reader' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047' (string)
info.vendor = 'VIA Technologies, Inc.' (string)
linux.device_file = '/dev/bus/usb/001/004' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1/usb1/1-5' (string)
usb_device.bus_number = 1 (0x1) (int)
usb_device.can_wake_up = false (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 0 (0x0) (int)
usb_device.device_protocol = 0 (0x0) (int)
usb_device.device_revision_bcd = 3 (0x3) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = false (bool)
usb_device.linux.device_number = 4 (0x4) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1/usb1/1-5' (string)
usb_device.max_power = 100 (0x64) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 0 (0x0) (int)
usb_device.product = 'USB 2.0 Card Reader' (string)
usb_device.product_id = 25093 (0x6205) (int)
usb_device.serial = '000000089047' (string)
usb_device.speed = 480.0 (480) (double)
usb_device.speed_bcd = 294912 (0x48000) (int)
usb_device.vendor = 'VIA Technologies, Inc.' (string)
usb_device.vendor_id = 1037 (0x40d) (int)
usb_device.version = 2.0 (2) (double)
usb_device.version_bcd = 512 (0x200) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0'
info.bus = 'usb' (string)
info.linux.driver = 'usb-storage' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047' (string)
info.product = 'USB Mass Storage Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1/usb1/1-5/1-5:1.0' (string)
usb.bus_number = 1 (0x1) (int)
usb.can_wake_up = false (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 0 (0x0) (int)
usb.device_protocol = 0 (0x0) (int)
usb.device_revision_bcd = 3 (0x3) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 8 (0x8) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 80 (0x50) (int)
usb.interface.subclass = 6 (0x6) (int)
usb.is_self_powered = false (bool)
usb.linux.device_number = 4 (0x4) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1/usb1/1-5/1-5:1.0' (string)
usb.max_power = 100 (0x64) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 0 (0x0) (int)
usb.product = 'USB Mass Storage Interface' (string)
usb.product_id = 25093 (0x6205) (int)
usb.serial = '000000089047' (string)
usb.speed = 480.0 (480) (double)
usb.speed_bcd = 294912 (0x48000) (int)
usb.vendor = 'VIA Technologies, Inc.' (string)
usb.vendor_id = 1037 (0x40d) (int)
usb.version = 2.0 (2) (double)
usb.version_bcd = 512 (0x200) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0_scsi_host'
info.capabilities = {'scsi_host'} (string list)
info.category = 'scsi_host' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0' (string)
info.product = 'SCSI Host Adapter' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0_scsi_host' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_host' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1/usb1/1-5/1-5:1.0/host4' (string)
scsi_host.host = 4 (0x4) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0_scsi_host_scsi_device_lun0'
info.bus = 'scsi' (string)
info.linux.driver = 'sd' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0_scsi_host' (string)
info.product = 'SCSI Device' (string)
info.subsystem = 'scsi' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0_scsi_host_scsi_device_lun0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1/usb1/1-5/1-5:1.0/host4/target4:0:0/4:0:0:0' (string)
scsi.bus = 0 (0x0) (int)
scsi.host = 4 (0x4) (int)
scsi.lun = 0 (0x0) (int)
scsi.model = 'VT6205-DevB' (string)
scsi.target = 0 (0x0) (int)
scsi.type = 'disk' (string)
scsi.vendor = 'VIA-P' (string)
udi = '/org/freedesktop/Hal/devices/storage_serial_VIA_P_VT6205_DevB_000000089047_0_0'
block.device = '/dev/sdc' (string)
block.is_volume = false (bool)
block.major = 8 (0x8) (int)
block.minor = 32 (0x20) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_VIA_P_VT6205_DevB_000000089047_0_0' (string)
info.addons = {'hald-addon-storage'} (string list)
info.capabilities = {'storage', 'block'} (string list)
info.category = 'storage' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0_scsi_host_scsi_device_lun0' (string)
info.product = 'VT6205-DevB' (string)
info.udi = '/org/freedesktop/Hal/devices/storage_serial_VIA_P_VT6205_DevB_000000089047_0_0' (string)
info.vendor = 'VIA-P' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/block/sdc' (string)
storage.automount_enabled_hint = true (bool)
storage.bus = 'usb' (string)
storage.drive_type = 'disk' (string)
storage.firmware_version = '2.82' (string)
storage.hotpluggable = true (bool)
storage.lun = 0 (0x0) (int)
storage.media_check_enabled = true (bool)
storage.model = 'VT6205-DevB' (string)
storage.no_partitions_hint = false (bool)
storage.originating_device = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0' (string)
storage.physical_device = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0' (string)
storage.removable = true (bool)
storage.removable.media_available = false (bool)
storage.requires_eject = false (bool)
storage.serial = 'VIA-P_VT6205-DevB_000000089047-0:0' (string)
storage.size = 0 (0x0) (uint64)
storage.vendor = 'VIA-P' (string)
udi = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0_scsi_host_scsi_device_lun0_scsi_generic'
info.capabilities = {'scsi_generic'} (string list)
info.category = 'scsi_generic' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0_scsi_host_scsi_device_lun0' (string)
info.product = 'SCSI Generic Interface' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_40d_6205_000000089047_if0_scsi_host_scsi_device_lun0_scsi_generic' (string)
linux.device_file = '/dev/sg2' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_generic' (string)
linux.sysfs_path = '/sys/class/scsi_generic/sg2' (string)
scsi_generic.device = '/dev/sg2' (string)
udi = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_1_if0'
info.bus = 'usb' (string)
info.linux.driver = 'hub' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_1' (string)
info.product = 'USB Hub Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_1_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1/usb1/1-0:1.0' (string)
usb.bus_number = 1 (0x1) (int)
usb.can_wake_up = true (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 9 (0x9) (int)
usb.device_protocol = 1 (0x1) (int)
usb.device_revision_bcd = 518 (0x206) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 9 (0x9) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 0 (0x0) (int)
usb.interface.subclass = 0 (0x0) (int)
usb.is_self_powered = true (bool)
usb.linux.device_number = 1 (0x1) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1/usb1/1-0:1.0' (string)
usb.max_power = 0 (0x0) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 10 (0xa) (int)
usb.product = 'USB Hub Interface' (string)
usb.product_id = 0 (0x0) (int)
usb.serial = '0000:00:02.1' (string)
usb.speed = 480.0 (480) (double)
usb.speed_bcd = 294912 (0x48000) (int)
usb.vendor = 'Linux 2.6.22-gentoo-r9 ehci_hcd' (string)
usb.vendor_id = 0 (0x0) (int)
usb.version = 2.0 (2) (double)
usb.version_bcd = 512 (0x200) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_5a'
info.bus = 'pci' (string)
info.linux.driver = 'ohci_hcd' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 USB Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_5a' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 16 (0x10) (int)
pci.device_subclass = 3 (0x3) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0' (string)
pci.product = 'CK804 USB Controller' (string)
pci.product_id = 90 (0x5a) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_0'
info.bus = 'usb_device' (string)
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_5a' (string)
info.product = 'OHCI Host Controller' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_0' (string)
info.vendor = 'Linux 2.6.22-gentoo-r9 ohci_hcd' (string)
linux.device_file = '/dev/bus/usb/002/001' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/usb2' (string)
usb_device.bus_number = 2 (0x2) (int)
usb_device.can_wake_up = true (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 9 (0x9) (int)
usb_device.device_protocol = 0 (0x0) (int)
usb_device.device_revision_bcd = 518 (0x206) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = true (bool)
usb_device.linux.device_number = 1 (0x1) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/usb2' (string)
usb_device.max_power = 0 (0x0) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 10 (0xa) (int)
usb_device.product = 'OHCI Host Controller' (string)
usb_device.product_id = 0 (0x0) (int)
usb_device.serial = '0000:00:02.0' (string)
usb_device.speed = 12.0 (12) (double)
usb_device.speed_bcd = 4608 (0x1200) (int)
usb_device.vendor = 'Linux 2.6.22-gentoo-r9 ohci_hcd' (string)
usb_device.vendor_id = 0 (0x0) (int)
usb_device.version = 1.1 (1.1) (double)
usb_device.version_bcd = 272 (0x110) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_45e_e1_noserial'
info.bus = 'usb_device' (string)
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_0' (string)
info.product = 'Microsoft Wireless Optical Mouse? 1.00' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_45e_e1_noserial' (string)
info.vendor = 'Microsoft Corp.' (string)
linux.device_file = '/dev/bus/usb/002/003' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/usb2/2-4' (string)
usb_device.bus_number = 2 (0x2) (int)
usb_device.can_wake_up = true (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 0 (0x0) (int)
usb_device.device_protocol = 0 (0x0) (int)
usb_device.device_revision_bcd = 7 (0x7) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = false (bool)
usb_device.linux.device_number = 3 (0x3) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/usb2/2-4' (string)
usb_device.max_power = 100 (0x64) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 0 (0x0) (int)
usb_device.product = 'Microsoft Wireless Optical Mouse? 1.00' (string)
usb_device.product_id = 225 (0xe1) (int)
usb_device.speed = 1.5 (1.5) (double)
usb_device.speed_bcd = 336 (0x150) (int)
usb_device.vendor = 'Microsoft Corp.' (string)
usb_device.vendor_id = 1118 (0x45e) (int)
usb_device.version = 2.0 (2) (double)
usb_device.version_bcd = 512 (0x200) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_45e_e1_noserial_if0'
info.bus = 'usb' (string)
info.linux.driver = 'usbhid' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_45e_e1_noserial' (string)
info.product = 'USB HID Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_45e_e1_noserial_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.0' (string)
usb.bus_number = 2 (0x2) (int)
usb.can_wake_up = true (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 0 (0x0) (int)
usb.device_protocol = 0 (0x0) (int)
usb.device_revision_bcd = 7 (0x7) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 3 (0x3) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 2 (0x2) (int)
usb.interface.subclass = 1 (0x1) (int)
usb.is_self_powered = false (bool)
usb.linux.device_number = 3 (0x3) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.0' (string)
usb.max_power = 100 (0x64) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 0 (0x0) (int)
usb.product = 'USB HID Interface' (string)
usb.product_id = 225 (0xe1) (int)
usb.speed = 1.5 (1.5) (double)
usb.speed_bcd = 336 (0x150) (int)
usb.vendor = 'Microsoft Corp.' (string)
usb.vendor_id = 1118 (0x45e) (int)
usb.version = 2.0 (2) (double)
usb.version_bcd = 512 (0x200) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_45e_e1_noserial_if0_logicaldev_input'
info.capabilities = {'input', 'input.mouse'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_45e_e1_noserial_if0' (string)
info.product = 'Microsoft Microsoft Wireless Optical Mouse? 1.00' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_45e_e1_noserial_if0_logicaldev_input' (string)
input.device = '/dev/input/event2' (string)
input.originating_device = '/org/freedesktop/Hal/devices/usb_device_45e_e1_noserial_if0' (string)
input.physical_device = '/org/freedesktop/Hal/devices/usb_device_45e_e1_noserial_if0' (string)
input.product = 'Microsoft Microsoft Wireless Optical Mouse? 1.00' (string)
linux.device_file = '/dev/input/event2' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/class/input/input2/event2' (string)
udi = '/org/freedesktop/Hal/devices/usb_device_c45_602c_noserial'
info.bus = 'usb_device' (string)
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_0' (string)
info.product = 'Clas Ohlson TWC-30XOP WebCam' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_c45_602c_noserial' (string)
info.vendor = 'Microdia' (string)
linux.device_file = '/dev/bus/usb/002/002' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/usb2/2-3' (string)
usb_device.bus_number = 2 (0x2) (int)
usb_device.can_wake_up = false (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 0 (0x0) (int)
usb_device.device_protocol = 0 (0x0) (int)
usb_device.device_revision_bcd = 257 (0x101) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = false (bool)
usb_device.linux.device_number = 2 (0x2) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/usb2/2-3' (string)
usb_device.max_power = 500 (0x1f4) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 0 (0x0) (int)
usb_device.product = 'Clas Ohlson TWC-30XOP WebCam' (string)
usb_device.product_id = 24620 (0x602c) (int)
usb_device.speed = 12.0 (12) (double)
usb_device.speed_bcd = 4608 (0x1200) (int)
usb_device.vendor = 'Microdia' (string)
usb_device.vendor_id = 3141 (0xc45) (int)
usb_device.version = 1.1 (1.1) (double)
usb_device.version_bcd = 272 (0x110) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_c45_602c_noserial_if0'
info.bus = 'usb' (string)
info.linux.driver = 'sn9c102' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_c45_602c_noserial' (string)
info.product = 'USB Vendor Specific Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_c45_602c_noserial_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/usb2/2-3/2-3:1.0' (string)
usb.bus_number = 2 (0x2) (int)
usb.can_wake_up = false (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 0 (0x0) (int)
usb.device_protocol = 0 (0x0) (int)
usb.device_revision_bcd = 257 (0x101) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 255 (0xff) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 255 (0xff) (int)
usb.interface.subclass = 255 (0xff) (int)
usb.is_self_powered = false (bool)
usb.linux.device_number = 2 (0x2) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/usb2/2-3/2-3:1.0' (string)
usb.max_power = 500 (0x1f4) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 0 (0x0) (int)
usb.product = 'USB Vendor Specific Interface' (string)
usb.product_id = 24620 (0x602c) (int)
usb.speed = 12.0 (12) (double)
usb.speed_bcd = 4608 (0x1200) (int)
usb.vendor = 'Microdia' (string)
usb.vendor_id = 3141 (0xc45) (int)
usb.version = 1.1 (1.1) (double)
usb.version_bcd = 272 (0x110) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_0_if0'
info.bus = 'usb' (string)
info.linux.driver = 'hub' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_0' (string)
info.product = 'USB Hub Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_00_02_0_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/usb2/2-0:1.0' (string)
usb.bus_number = 2 (0x2) (int)
usb.can_wake_up = true (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 9 (0x9) (int)
usb.device_protocol = 0 (0x0) (int)
usb.device_revision_bcd = 518 (0x206) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 9 (0x9) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 0 (0x0) (int)
usb.interface.subclass = 0 (0x0) (int)
usb.is_self_powered = true (bool)
usb.linux.device_number = 1 (0x1) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/usb2/2-0:1.0' (string)
usb.max_power = 0 (0x0) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 10 (0xa) (int)
usb.product = 'USB Hub Interface' (string)
usb.product_id = 0 (0x0) (int)
usb.serial = '0000:00:02.0' (string)
usb.speed = 12.0 (12) (double)
usb.speed_bcd = 4608 (0x1200) (int)
usb.vendor = 'Linux 2.6.22-gentoo-r9 ohci_hcd' (string)
usb.vendor_id = 0 (0x0) (int)
usb.version = 1.1 (1.1) (double)
usb.version_bcd = 272 (0x110) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_52'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 SMBus' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_52' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:01.1' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 5 (0x5) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:01.1' (string)
pci.product = 'CK804 SMBus' (string)
pci.product_id = 82 (0x52) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_51'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 ISA Bridge' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_51' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:01.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 1 (0x1) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:01.0' (string)
pci.product = 'CK804 ISA Bridge' (string)
pci.product_id = 81 (0x51) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
udi = '/org/freedesktop/Hal/devices/pci_10de_5e'
info.bus = 'pci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'CK804 Memory Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10de_5e' (string)
info.vendor = 'nVidia Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:00.0' (string)
pci.device_class = 5 (0x5) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 128 (0x80) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:00.0' (string)
pci.product = 'CK804 Memory Controller' (string)
pci.product_id = 94 (0x5e) (int)
pci.subsys_product_id = 10389 (0x2895) (int)
pci.subsys_vendor = 'Tyan Computer' (string)
pci.subsys_vendor_id = 4337 (0x10f1) (int)
pci.vendor = 'nVidia Corporation' (string)
pci.vendor_id = 4318 (0x10de) (int)
Dumped 125 device(s) from the Global Device List.
------------------------------------------------