rendered paste bodyBootdata ok (command line is ro root=LABEL=/ rhgb quiet)
Linux version 2.6.18-8.el5xen (mockbuild@builder6.centos.org) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-52)) #1 SMP Thu Mar 15 19:56:43 EDT 2007
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 00000001f0b52000 (usable)
On node 0 totalpages: 2034514
DMA zone: 2034514 pages, LIFO batch:31
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x00000000000f5e80
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x00000000bff63681
ACPI: FADT (v001 INTEL TUMWATER 0x06040000 PTL 0x00000003) @ 0x00000000bff68e48
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x00000000bff68ebc
ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x00000000bff68f4c
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x00000000bff68f88
ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @ 0x00000000bff68fb0
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20050228) @ 0x00000000bff636bd
ACPI: DSDT (v001 Intel BLAKFORD 0x06040000 MSFT 0x0100000e) @ 0x0000000000000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x06] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x07] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfec81000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 32, address 0xfec81000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to xen
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
Built 1 zonelists. Total pages: 2034514
Kernel command line: ro root=LABEL=/ rhgb quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Xen reported: 3000.144 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Software IO TLB enabled:
Aperture: 64 megabytes
Kernel range: 0xffff88000aab7000 - 0xffff88000eab7000
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Memory: 7897584k/8138056k available (2321k kernel code, 231568k reserved, 1312k data, 168k init)
Calibrating delay using timer specific routine.. 7502.96 BogoMIPS (lpj=15005926)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
(SMP-)alternatives turned off
ACPI: Core revision 20060707
Initializing CPU#1
Initializing CPU#2
Brought up 4 CPUs
sizeof(vma)=168 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=240 bytes
Initializing CPU#3
migration_cost=3753
checking if image is initramfs... it is
Grant table initialized
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: PXH quirk detected, disabling MSI for SHPC device
Boot video device is 0000:08:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3.BMD0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3.BMD0.BPD0.PXH0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3.BMD0.BPD2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3.BMF3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 14 15) *9
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
xen_mem: Initialising balloon driver.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
PCI: Bridge: 0000:00:02.0
IO window: 2000-2fff
MEM window: d4300000-d43fffff
PREFETCH window: d0000000-d1ffffff
PCI: Bridge: 0000:04:00.0
IO window: 3000-3fff
MEM window: d4100000-d41fffff
PREFETCH window: d4400000-d44fffff
PCI: Bridge: 0000:03:00.0
IO window: 3000-3fff
MEM window: d4100000-d41fffff
PREFETCH window: d4400000-d44fffff
PCI: Bridge: 0000:03:02.0
IO window: 4000-4fff
MEM window: d4000000-d40fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:02:00.0
IO window: 3000-4fff
MEM window: d4000000-d41fffff
PREFETCH window: d4400000-d44fffff
PCI: Bridge: 0000:02:00.3
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
IO window: 3000-4fff
MEM window: d4000000-d42fffff
PREFETCH window: d4400000-d44fffff
PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:08:00.0
PCI: Bridge: 0000:00:04.0
IO window: 5000-5fff
MEM window: d2000000-d3ffffff
PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
GSI 16 sharing vector 0xA0 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.0 to 64
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:03.0 to 64
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:03:00.0 to 64
PCI: Setting latency timer of device 0000:04:00.0 to 64
GSI 17 sharing vector 0xA8 and IRQ 17
ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:03:02.0 to 64
PCI: Setting latency timer of device 0000:02:00.3 to 64
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
Simple Boot Flag at 0x38 set to 0x1
IA-32 Microcode Update Driver: v1.14-xen <tigran@veritas.com>
audit: initializing netlink socket (disabled)
audit(1189604837.440:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 991108A46E99ED4B
- User ID: CentOS (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
PCI: Setting latency timer of device 0000:02:00.0 to 64
Allocate Port Service[0000:02:00.0:pcie10]
PCI: Setting latency timer of device 0000:03:00.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:03:00.0:pcie20]
PCI: Setting latency timer of device 0000:03:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:03:02.0:pcie20]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x1
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x3
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x4
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x5
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x6
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x7
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Xen virtual console successfully installed as ttyS0
Event-channel device installed.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ESB2: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
ESB2: chipset revision 9
ESB2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1880-0x1887, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: SONY DVD RW AW-Q170A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Write protecting the kernel read-only data: 439k
input: AT Translated Set 2 keyboard as /class/input/input0
USB Universal Host Controller Interface driver v3.0
GSI 18 sharing vector 0xB0 and IRQ 18
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 17 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 18, io base 0x00001800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
GSI 19 sharing vector 0xB8 and IRQ 19
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 17, io base 0x00001840
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 17 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 18, io mem 0xd4604000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
input: ImExPS/2 Generic Explorer Mouse as /class/input/input1
SCSI subsystem initialized
libata version 2.00 loaded.
ahci 0000:00:1f.2: version 2.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports ? Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit stag led pmp
ata1: SATA max UDMA/133 cmd 0xFFFFC20000026500 ctl 0x0 bmdma 0x0 irq 19
ata2: SATA max UDMA/133 cmd 0xFFFFC20000026580 ctl 0x0 bmdma 0x0 irq 19
ata3: SATA max UDMA/133 cmd 0xFFFFC20000026600 ctl 0x0 bmdma 0x0 irq 19
ata4: SATA max UDMA/133 cmd 0xFFFFC20000026680 ctl 0x0 bmdma 0x0 irq 19
ata5: SATA max UDMA/133 cmd 0xFFFFC20000026700 ctl 0x0 bmdma 0x0 irq 19
ata6: SATA max UDMA/133 cmd 0xFFFFC20000026780 ctl 0x0 bmdma 0x0 irq 19
scsi0 : ahci
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7, max UDMA/133, 781422768 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 0
ata1.00: configured for UDMA/133
scsi1 : ahci
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7, max UDMA/133, 781422768 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 0
ata2.00: configured for UDMA/133
scsi2 : ahci
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : ahci
ata4: SATA link down (SStatus 0 SControl 300)
scsi4 : ahci
ata5: SATA link down (SStatus 0 SControl 300)
scsi5 : ahci
ata6: SATA link down (SStatus 0 SControl 300)
Vendor: ATA Model: WDC WD4000AAKS-0 Rev: 12.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
Vendor: ATA Model: WDC WD4000AAKS-0 Rev: 12.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 781422768 512-byte hdwr sectors (400088 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 781422768 512-byte hdwr sectors (400088 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: Attached scsi disk sdb
3ware 9000 Storage Controller device driver for Linux v2.26.06.002.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:01:00.0 to 64
3w-9xxx: scsi6: AEN: INFO (0x04:0x0001): Controller reset occurred:resets=1.
3w-9xxx: scsi6: AEN: INFO (0x04:0x0053): Battery capacity test is overdue:.
3w-9xxx: scsi6: AEN: INFO (0x04:0x0053): Battery capacity test is overdue:.
scsi6 : 3ware 9000 Storage Controller
3w-9xxx: scsi6: Found a 3ware 9000 Storage Controller at 0xd4300000, IRQ: 16.
3w-9xxx: scsi6: Firmware FE9X 3.08.02.005, BIOS BE9X 3.08.00.002, Ports: 8.
Vendor: AMCC Model: 9650SE-8LP DISK Rev: 3.08
Type: Direct-Access ANSI SCSI revision: 05
sdc : very big device. try to use READ CAPACITY(16).
SCSI device sdc: 4394465280 512-byte hdwr sectors (2249966 MB)
sdc: Write Protect is off
sdc: Mode Sense: 23 00 00 00
SCSI device sdc: drive cache: write back, no read (daft)
sdc : very big device. try to use READ CAPACITY(16).
SCSI device sdc: 4394465280 512-byte hdwr sectors (2249966 MB)
sdc: Write Protect is off
sdc: Mode Sense: 23 00 00 00
SCSI device sdc: drive cache: write back, no read (daft)
sdc: sdc1
sd 6:0:0:0: Attached scsi disk sdc
Vendor: AMCC Model: 9650SE-8LP DISK Rev: 3.08
Type: Direct-Access ANSI SCSI revision: 05
sdd : very big device. try to use READ CAPACITY(16).
SCSI device sdd: 4394465280 512-byte hdwr sectors (2249966 MB)
sdd: Write Protect is off
sdd: Mode Sense: 23 00 00 00
SCSI device sdd: drive cache: write back, no read (daft)
sdd : very big device. try to use READ CAPACITY(16).
SCSI device sdd: 4394465280 512-byte hdwr sectors (2249966 MB)
sdd: Write Protect is off
sdd: Mode Sense: 23 00 00 00
SCSI device sdd: drive cache: write back, no read (daft)
sdd: sdd1
sd 6:0:1:0: Attached scsi disk sdd
ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 16 (level, low) -> IRQ 16
scsi7 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 29320A Ultra320 SCSI adapter>
aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1189604867.517:2): enforcing=1 old_enforcing=0 auid=4294967295
security: 3 users, 6 roles, 1587 types, 172 bools, 1 sens, 1024 cats
security: 59 classes, 49762 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev sda2, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1189604867.777:3): policy loaded auid=4294967295
input: PC Speaker as /class/input/input2
Intel(R) PRO/1000 Network Driver - version 7.2.7-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:06:00.0 to 64
e1000: 0000:06:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:30:48:7b:18:a4
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:06:00.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:06:00.1 to 64
e1000: 0000:06:00.1: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:30:48:7b:18:a5
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 6:0:0:0: Attached scsi generic sg2 type 0
sd 6:0:1:0: Attached scsi generic sg3 type 0
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
intel_rng: FWH not detected
Floppy drive(s): fd0 is 1.44M
hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
FDC 0 is a post-1991 82077
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
8250_pnp: Unknown symbol serial8250_unregister_port
8250_pnp: Unknown symbol serial8250_register_port
8250_pnp: Unknown symbol serial8250_unregister_port
8250_pnp: Unknown symbol serial8250_register_port
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.11.0-ioctl (2006-09-14) initialised: dm-devel@redhat.com
EXT3 FS on sda2, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sdb2, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sdb3, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 4096532k swap on /dev/sdb1. Priority:-1 extents:1 across:4096532k
Adding 4096564k swap on /dev/sda3. Priority:-2 extents:1 across:4096564k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 304 bytes per conntrack
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.lo.retrans_time; Use net.ipv6.neigh.lo.retrans_time_ms instead.
ADDRCONF(NETDEV_UP): eth0: link is not ready
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ADDRCONF(NETDEV_UP): eth1: link is not ready
e1000: eth1: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
audit(1189604883.327:4): audit_pid=2805 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SELinux: initialized (dev nfsd, type nfsd), uses genfs_contexts
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
eth0: no IPv6 routers present
eth1: no IPv6 routers present
Bridge firewalling registered
device vif0.1 entered promiscuous mode
xenbr1: port 1(vif0.1) entering learning state
xenbr1: topology change detected, propagating
xenbr1: port 1(vif0.1) entering forwarding state
ADDRCONF(NETDEV_UP): peth1: link is not ready
e1000: peth1: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): peth1: link becomes ready
device peth1 entered promiscuous mode
xenbr1: port 2(peth1) entering learning state
xenbr1: topology change detected, propagating
xenbr1: port 2(peth1) entering forwarding state
eth1: no IPv6 routers present
Module Size Used by
bridge 91889 0
netloop 39873 0
netbk 128897 0 [permanent]
blktap 417765 2 [permanent]
blkbk 52857 0 [permanent]
nfsd 280873 17
exportfs 38849 1 nfsd
lockd 96337 2 nfsd
nfs_acl 36673 1 nfsd
autofs4 56393 2
hidp 83649 2
rfcomm 104809 0
l2cap 89281 10 hidp,rfcomm
bluetooth 118725 5 hidp,rfcomm,l2cap
sunrpc 195593 12 nfsd,lockd,nfs_acl
ipv6 411169 28
ip_conntrack_ftp 41489 0
ip_conntrack_netbios_ns 36033 0
ipt_REJECT 38849 1
xt_state 35265 9
ip_conntrack 91365 3 ip_conntrack_ftp,ip_conntrack_netbios_ns,xt_state
nfnetlink 40457 1 ip_conntrack
xt_tcpudp 36417 11
iptable_filter 36161 1
ip_tables 55329 1 iptable_filter
x_tables 50249 4 ipt_REJECT,xt_state,xt_tcpudp,ip_tables
dm_mirror 61121 0
dm_mod 93969 1 dm_mirror
video 51273 0
sbs 49921 0
i2c_ec 38593 1 sbs
button 40545 0
battery 43849 0
asus_acpi 50917 0
ac 38729 0
lp 47120 0
snd_hda_intel 52189 0
snd_hda_codec 215233 1 snd_hda_intel
snd_seq_dummy 37061 0
snd_seq_oss 65601 0
i2c_i801 41429 0
i2c_core 56129 2 i2c_ec,i2c_i801
snd_seq_midi_event 41025 1 snd_seq_oss
ide_cd 73441 0
floppy 92905 0
snd_seq 88033 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
serial_core 55233 0
shpchp 70509 0
parport_pc 62313 1
parport 73293 2 lp,parport_pc
snd_seq_device 41813 3 snd_seq_dummy,snd_seq_oss,snd_seq
sg 69609 0
cdrom 68841 1 ide_cd
snd_pcm_oss 77537 0
snd_mixer_oss 50113 1 snd_pcm_oss
snd_pcm 116809 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
e1000 156625 0
serio_raw 40517 0
snd_timer 57673 2 snd_seq,snd_pcm
snd 95209 9 snd_hda_intel,snd_hda_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 43873 1 snd
snd_page_alloc 43345 2 snd_hda_intel,snd_pcm
pcspkr 36289 0
aic79xx 202393 0
scsi_transport_spi 59713 1 aic79xx
3w_9xxx 67844 0
ahci 52805 6
libata 139113 1 ahci
sd_mod 54081 8
scsi_mod 184057 7 sg,aic79xx,scsi_transport_spi,3w_9xxx,ahci,libata,sd_mod
ext3 166353 4
jbd 93617 1 ext3
ehci_hcd 65357 0
ohci_hcd 54621 0
uhci_hcd 57561 0
00:00.0 0600: 8086:25c0 (rev 31)
00:02.0 0604: 8086:25e2 (rev 31)
00:03.0 0604: 8086:25e3 (rev 31)
00:04.0 0604: 8086:25fa (rev 31)
00:08.0 0880: 8086:1a38 (rev 31)
00:10.0 0600: 8086:25f0 (rev 31)
00:10.1 0600: 8086:25f0 (rev 31)
00:10.2 0600: 8086:25f0 (rev 31)
00:11.0 0600: 8086:25f1 (rev 31)
00:13.0 0600: 8086:25f3 (rev 31)
00:15.0 0600: 8086:25f5 (rev 31)
00:16.0 0600: 8086:25f6 (rev 31)
00:1b.0 0403: 8086:269a (rev 09)
00:1d.0 0c03: 8086:2688 (rev 09)
00:1d.1 0c03: 8086:2689 (rev 09)
00:1d.2 0c03: 8086:268a (rev 09)
00:1d.3 0c03: 8086:268b (rev 09)
00:1d.7 0c03: 8086:268c (rev 09)
00:1e.0 0604: 8086:244e (rev d9)
00:1f.0 0601: 8086:2670 (rev 09)
00:1f.1 0101: 8086:269e (rev 09)
00:1f.2 0106: 8086:2681 (rev 09)
00:1f.3 0c05: 8086:269b (rev 09)
01:00.0 0104: 13c1:1004 (rev 01)
02:00.0 0604: 8086:3500 (rev 01)
02:00.3 0604: 8086:350c (rev 01)
03:00.0 0604: 8086:3510 (rev 01)
03:02.0 0604: 8086:3518 (rev 01)
04:00.0 0604: 8086:032c (rev 09)
05:01.0 0100: 9005:8000 (rev 10)
06:00.0 0200: 8086:1096 (rev 01)
06:00.1 0200: 8086:1096 (rev 01)
08:00.0 0300: 10de:029e (rev a1)