rendered paste bodyec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
Entering add_active_range(0, 0, 229376) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
early_node_map[1] active PFN ranges
0: 0 -> 229376
On node 0 totalpages: 229376
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 CN700 ) @ 0x000f7a90
ACPI: RSDT (v001 CN700 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3bee3040
ACPI: FADT (v001 CN700 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3bee30c0
ACPI: MADT (v001 CN700 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3bee81c0
ACPI: DSDT (v001 CN700 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
Allocating PCI resources starting at 40000000 (gap: 3bf00000:c2d00000)
Detected 1500.084 MHz processor.
Built 1 zonelists. Total pages: 227584
Kernel command line: auto BOOT_IMAGE=SlackRT ro root=301 splash=silent
bootsplash: silent mode.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
I-pipe 1.8-02: pipeline enabled.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 905664k/917504k available (2232k kernel code, 11364k reserved, 753k data, 160k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffff8000 - 0xfffff000 ( 28 kB)
vmalloc : 0xf8800000 - 0xffff6000 ( 119 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc03ee000 - 0xc0416000 ( 160 kB)
.data : 0xc032e2b6 - 0xc03ea9d4 ( 753 kB)
.text : 0xc0100000 - 0xc032e2b6 (2232 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3000.48 BogoMIPS (lpj=1500240)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7c9baff 00100000 00000000 00000000 00000001 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 128K (64 bytes/line)
CPU: After all inits, caps: 27c9baff 00100000 00000000 00000000 00000001 00003fcc 00000000
CPU: Centaur VIA Esther processor 1500MHz stepping 09
Checking 'hlt' instruction... OK.
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0e20)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf9460, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: MSI-K8T-Neo2Fir, attempting to turn soundcard ON
PCI: MSI-K8T-Neo2Fir, soundcard on
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs *20), disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
ACPI: PCI Interrupt Link [ALKD] (IRQs *23), disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: e000-efff
MEM window: fb000000-fcffffff
PREFETCH window: f4000000-f7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 59k freed
io scheduler noop registered
io scheduler cfq registered (default)
0000:00:10.4 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
vesafb: framebuffer at 0xf4000000, mapped to 0xf8880000, using 6144k, total 65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:adbb
vesafb: pmi: set display start = c00cae09, set palette = c00cae7a
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 23695 bytes,<6>...found (1024x768, 37626 bytes, v3).
Console: switching to colour frame buffer device 118x36
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA VT3314 chipset
agpgart: AGP aperture is 128M @ 0xe8000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: TOSHIBA MK3018GAS, ATA DISK drive
hdb: CD-ROM Drive/F5B, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB), CHS=58140/16/63
hda: cache flushes supported
hda: hda1 hda2 < hda5 >
hdb: ATAPI 48X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 11, io mem 0xfdffd000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
PCI: VIA VLink IRQ fixup for 0000:00:10.0, from 5 to 10
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 10, io base 0x0000fe00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
PCI: VIA VLink IRQ fixup for 0000:00:10.1, from 5 to 10
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 10, io base 0x0000fd00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 11, io base 0x0000fc00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 11, io base 0x0000fb00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Time: tsc clocksource has been installed.
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
RAMDISK: Couldn't find valid RAM disk image starting at 0.
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 160k freed
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
[drm] Initialized via 2.10.0 20060529 on minor 0
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 0:0:0:0: Direct-Access Verbatim USB Drive 2.00 PQ: 0 ANSI: 2
ready
SCSI device sda: 256000 512-byte hdwr sectors (131 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 256000 512-byte hdwr sectors (131 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda: unknown partition table
sd 0:0:0:0: Attached scsi removable disk sda
usb-storage: device scan complete
I-pipe: Domain RTAI registered.
RTAI[hal]: <magma> mounted over IPIPE-NOTHREADS 1.8-02.
RTAI[hal]: compiled with gcc version 3.4.6.
RTAI[hal]: mounted (IPIPE-NOTHREADS, IMMEDIATE (INTERNAL IRQs VECTORED), ISOL_CPUS_MASK: 0).
PIPELINE layers:
f8e8fc80 9ac15d93 RTAI 200
c03c7b80 0 Linux 100
RTAI[malloc]: vmalloced extent f9160000, size 2097152.
RTAI[malloc]: loaded (global heap size=2097152 bytes).
RTAI[malloc]: kmalloced extent f0900000, size 131072.
RTAI[sched]: loaded (IMMEDIATE, UP, USER/KERNEL SPACE: <with RTAI OWN KTASKs>).
RTAI[sched]: hard timer type/freq = 8254-PIT/1193180(Hz); default timing mode is periodic; linear ordering of timed lists.
RTAI[sched]: Linux timer freq = 1000 (Hz), CPU freq = 1500084000 hz.
RTAI[sched]: timer setup = 2010 ns, resched latency = 2689 ns.
RTAI[math]: loaded.
RTAPI: Init
RTAPI: Init complete
RTAPI: Exiting
RTAPI: Exit complete
RTAI[math]: unloaded.
RTAI[malloc]: vfreed extent f9160000, size 2097152.
RTAI[malloc]: unloaded.
RTAI[malloc]: kfreed extent f0900000, size 131072.
RTAI[sched]: unloaded (forced hard/soft/hard transitions: traps 0, syscalls 0).
I-pipe: Domain RTAI unregistered.
RTAI[hal]: unmounted.
I-pipe: Domain RTAI registered.
RTAI[hal]: <magma> mounted over IPIPE-NOTHREADS 1.8-02.
RTAI[hal]: compiled with gcc version 3.4.6.
RTAI[hal]: mounted (IPIPE-NOTHREADS, IMMEDIATE (INTERNAL IRQs VECTORED), ISOL_CPUS_MASK: 0).
PIPELINE layers:
f8e8fc80 9ac15d93 RTAI 200
c03c7b80 0 Linux 100
RTAI[malloc]: vmalloced extent f9160000, size 2097152.
RTAI[malloc]: loaded (global heap size=2097152 bytes).
RTAI[malloc]: kmalloced extent f0b60000, size 131072.
RTAI[sched]: loaded (IMMEDIATE, UP, USER/KERNEL SPACE: <with RTAI OWN KTASKs>).
RTAI[sched]: hard timer type/freq = 8254-PIT/1193180(Hz); default timing mode is periodic; linear ordering of timed lists.
RTAI[sched]: Linux timer freq = 1000 (Hz), CPU freq = 1500084000 hz.
RTAI[sched]: timer setup = 2010 ns, resched latency = 2689 ns.
RTAI[math]: loaded.
RTAPI: Init
RTAPI: Init complete
RTAPI: Exiting
RTAPI: Exit complete
RTAI[math]: unloaded.
RTAI[malloc]: vfreed extent f9160000, size 2097152.
RTAI[malloc]: unloaded.
RTAI[malloc]: kfreed extent f0b60000, size 131072.
RTAI[sched]: unloaded (forced hard/soft/hard transitions: traps 0, syscalls 0).
I-pipe: Domain RTAI unregistered.
RTAI[hal]: unmounted.
I-pipe: Domain RTAI registered.
RTAI[hal]: <magma> mounted over IPIPE-NOTHREADS 1.8-02.
RTAI[hal]: compiled with gcc version 3.4.6.
RTAI[hal]: mounted (IPIPE-NOTHREADS, IMMEDIATE (INTERNAL IRQs VECTORED), ISOL_CPUS_MASK: 0).
PIPELINE layers:
f8e8fc80 9ac15d93 RTAI 200
c03c7b80 0 Linux 100
RTAI[malloc]: vmalloced extent f9160000, size 2097152.
RTAI[malloc]: loaded (global heap size=2097152 bytes).
RTAI[malloc]: kmalloced extent f02c0000, size 131072.
RTAI[sched]: loaded (IMMEDIATE, UP, USER/KERNEL SPACE: <with RTAI OWN KTASKs>).
RTAI[sched]: hard timer type/freq = 8254-PIT/1193180(Hz); default timing mode is periodic; linear ordering of timed lists.
RTAI[sched]: Linux timer freq = 1000 (Hz), CPU freq = 1500084000 hz.
RTAI[sched]: timer setup = 2010 ns, resched latency = 2689 ns.
RTAI[math]: loaded.
RTAPI: Init
RTAPI: Init complete
RTAPI: Exiting
RTAPI: Exit complete
RTAI[math]: unloaded.
RTAI[malloc]: vfreed extent f9160000, size 2097152.
RTAI[malloc]: unloaded.
RTAI[malloc]: kfreed extent f02c0000, size 131072.
RTAI[sched]: unloaded (forced hard/soft/hard transitions: traps 0, syscalls 0).
I-pipe: Domain RTAI unregistered.
RTAI[hal]: unmounted.
usb 1-1: USB disconnect, address 2
usb 1-1: new high speed USB device using ehci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi 1:0:0:0: Direct-Access Verbatim USB Drive 2.00 PQ: 0 ANSI: 2
ready
SCSI device sda: 256000 512-byte hdwr sectors (131 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 256000 512-byte hdwr sectors (131 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda: unknown partition table
sd 1:0:0:0: Attached scsi removable disk sda
usb-storage: device scan complete