rendered paste body;This profile is designed specifically for LulzBot TAZ6 3D Printer
;Basic slice data:
;Sliced at: {day} {date} {time}
;Layer height: {layer_height}
;Walls: {wall_thickness}
;Fill: {fill_density}
;Estimated Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
G26 ; clear potential 'probe fail' condition
G21 ; set units to Millimetres
M107 ; disable fans
G90 ; absolute positioning
T0 ; select this extruder first
M82 ; set extruder to absolute mode
G92 E0 ; set extruder position to 0
M140 S{print_bed_temperature}; get bed heating up
M104 S170 T0 ; soften filament
M104 S170 T1 ; soften filament
G28 X Y ; home X and Y
G1 X-19 Y258 ; move over the Z_MIN switch
M109 R170 T0 ; wait for T0 to reach temp
M109 R170 T1 ; wait for T1 to reach temp
G28 Z ; home Z
G1 E-30 F100 ; suck up XXmm of filament
T1 ; switch extruders
G92 E0 ; set E to 0
G1 E-15 F100 ; suck up filament
T0 ; switch extruders
G92 E-60 ; adjust E value
G1 X-17 Y100 F3000 ; move above wiper pad
G1 Z1 ; push nozzle into wiper
G1 X-19 Y95 F1000 ; slow wipe
G1 X-17 Y90 F1000 ; slow wipe
G1 X-19 Y85 F1000 ; slow wipe
G1 X-17 Y90 F1000 ; slow wipe
G1 X-19 Y80 F1000 ; slow wipe
G1 X-17 Y95 F1000 ; slow wipe
G1 X-19 Y75 F2000 ; fast wipe
G1 X-17 Y85 F2000 ; fast wipe
G1 X-19 Y80 F2000 ; fast wipe
G1 X-17 Y70 F2000 ; fast wipe
G1 X-19 Y75 F2000 ; fast wipe
G1 X-17 Y95 F1000 ; slow wipe
G1 X-19 Y90 F1000 ; slow wipe
G1 X-17 Y85 F1000 ; slow wipe
G1 X-19 Y90 F1000 ; slow wipe
G1 X-17 Y80 F1000 ; slow wipe
G1 X-19 Y95 F1000 ; slow wipe
G1 X-17 Y75 F2000 ; fast wipe
G1 X-19 Y85 F2000 ; fast wipe
G1 X-17 Y80 F2000 ; fast wipe
G1 X-19 Y90 F2000 ; fast wipe
G1 X-17 Y85 F2000 ; fast wipe
G1 Z10 ; raise extruder
M109 R170 ; heat to probe temp
G1 X-9 Y-9 ; move above first probe point
M204 S100 ; set accel for probing
G29 ; probe sequence (for auto-leveling)
M204 S500 ; set accel back to normal
G1 X0 Y0 Z15 F5000 ; get out the way
M400 ; clear buffer
M140 S{print_bed_temperature}; get bed heating up
M104 S{print_temperature} T0 ; set extruder temp
M104 S{print_temperature2} T1; set extruder temp
M109 R{print_temperature} T0 ; set extruder temp and wait
M109 R{print_temperature2} T1; set extruder temp and wait
T1 ; switch to second extruder
G1 E0 F100 ; prime nozzle from previous print
G1 F100 E-{retraction_dual_amount} ;retract second nozzle before print
G92 E-30 ; adjust to 1st nozzle e value
T0 ; switch back to back
M190 R{print_bed_temperature}; get bed temping up during first layer
G1 Z2 E0 F75 ; extrude filament back into nozzle
M117 TAZ Printing... ; LCD status message